74LV4066PW,118
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 14-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 14 |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2007 |
| JESD-609 Code | e4 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| Resistance | 40Ohm |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Max Power Dissipation | 400mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 3.3V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | 74LV4066 |
| Pin Count | 14 |
| Operating Supply Voltage | 3.3V |
| Number of Channels | 1 |
| Voltage | 6V |
| Max Supply Voltage | 6V |
| Min Supply Voltage | 1V |
| Operating Supply Current | 80μA |
| Power Dissipation | 400mW |
| Max Supply Current | 80μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 40 ns |
| Number of Inputs | 4 |
| Supply Type | Single |
| Turn-Off Delay Time | 50 ns |
| -3db Bandwidth | 200MHz |
| On-State Resistance (Max) | 35Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 50 dB |
| Current - Leakage (IS(off)) (Max) | 2μA |
| Channel Capacitance (CS(off), CD(off)) | 3.5pF |
| On-state Resistance Match-Nom | 2Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 16ns, 28ns |
| Crosstalk | -60dB @ 1MHz |
| Switch-on Time-Max | 30ns |
| Voltage - Supply, Single (V+) | 1V~6V |
| Height Seated (Max) | 1.1mm |
| Length | 5mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
74LV4066PW,118 Overview
Shipping overseas is convenient due to the electrical component's packing in 14-TSSOP (0.173, 4.40mm Width). High reliability is ensured by the advanced packaging method Tape & Reel (TR). In Surface Mount, this analog switch is mounted. In the multiplexer and demultiplexer, 1:1 represents the number of circuits. Increasing operating temperature to around -40°C~125°C TA. 14 terminations have been made so far. This electronic part offers high-quality output due to its 1 channels. In the case of a voltage supply of 3.3V volts, the electrical part can be powered up and run. It is part of the design of the 14 series that this electronic component is included. A SPST - NO switching circuit is used to build these analog multiplexers. Try searching with 74LV4066 to find analog multiplexer variants. A 40Ohm internal resistance characterizes this multiplexer. The datasheets for the 14 pins explain the functions. Users shouldn't supply more than 6V voltage to the switch device. Analogue multiplexers of the Single supply type that are cost-effective. There should be 1V voltage fed to the electrical part below 1V. In order to operate this switch device, it would need a current of 80μA. The voltage required by this switch device is 1V~6V, draining from a single voltage supply. If put voltage greater than 80μA on the device, damage may be caused to the analogue multiplexer. There is a voltage range of 3.3V operating voltages for the electrical part. A 4 input needs to be operated.
74LV4066PW,118 Features
1 Channels
Switch Circuit: SPST - NO
80μA Supply Current
-3db Bandwidth: 200MHz
74LV4066PW,118 Applications
There are a lot of Nexperia USA Inc. 74LV4066PW,118 Analog Switches & Multiplexers ICs applications.
- Power routing
- Relay Replacement
- Microwave transmission systems
- Avionics and Military Systems
- Data Acquisition Systems
- Precision data acquisition
- T1/E1 Terminals
- SONET
- USB 1.1 signal switching circuits
- PBXs
