Parameters |
Factory Lead Time |
1 Week |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
6-TSSOP, SC-88, SOT-363 |
Number of Pins |
6 |
Operating Temperature |
-40°C~125°C TA |
Packaging |
Tape & Reel (TR) |
Published |
2003 |
JESD-609 Code |
e3 |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
6 |
Resistance |
15Ohm |
Terminal Finish |
Tin (Sn) |
Max Power Dissipation |
250mW |
Technology |
CMOS |
Terminal Position |
DUAL |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
1 |
Supply Voltage |
2.7V |
Time@Peak Reflow Temperature-Max (s) |
30 |
Base Part Number |
74LVC1G3157 |
Pin Count |
6 |
Number of Channels |
2 |
Number of Circuits |
1 |
Max Supply Voltage |
5.5V |
Min Supply Voltage |
1.65V |
Operating Supply Current |
40μA |
Power Dissipation |
250mW |
Propagation Delay |
1 ns |
Turn On Delay Time |
8.7 ns |
Logic Function |
Demultiplexer, Demux, Multiplexer, Mux |
Number of Inputs |
2 |
Supply Type |
Single |
Bandwidth |
300MHz |
Turn-Off Delay Time |
6 ns |
On-State Resistance (Max) |
10Ohm |
Multiplexer/Demultiplexer Circuit |
2:1 |
Off-state Isolation-Nom |
42 dB |
Current - Leakage (IS(off)) (Max) |
5μA |
Channel Capacitance (CS(off), CD(off)) |
6pF |
Switch Circuit |
SPDT |
Switch Time (Ton, Toff) (Max) |
4ns, 3.5ns |
Charge Injection |
7.5pC |
Switch-off Time-Max |
5ns |
Voltage - Supply, Single (V+) |
1.65V~5.5V |
Radiation Hardening |
No |
REACH SVHC |
No SVHC |
RoHS Status |
ROHS3 Compliant |
Lead Free |
Lead Free |
74LVC1G3157GW,125 Overview
Shipping overseas is convenient with the electronic component packed in 6-TSSOP, SC-88, SOT-363. High reliability is achieved by using advanced packaging method Tape & Reel (TR). A switch device like this is mounted in Surface Mount. 2:1 is the ratio between multiplexers and demultiplexers. Extended operating temperature around -40°C~125°C TA. The total number of terminations is 6. Due to its 2 channels, the electrical component produces high-quality output. Turning on and running the electrical part should be easy with a 2.7V voltage supply. There are 6 pins injected into the electronic part body. Multiplexers built on a SPDT switching circuit are built. The circuits in this analogue multiplexer number 1. Try searching with 74LVC1G3157 if you're looking for variants. This digital multiplexer has 15Ohm internal resistance. Datasheets for 6 pin functions are available upon request. normally, users should not supply switches with voltages higher than 5.5V. The digital multiplexer has a low cost Single supply. 1.65V is the lowest voltage that should be fed to the electronic electronic part. For this digital switch to work, 40μA current would suffice. Analogue multiplexers require a 1.65V~5.5V voltage to drain from a single voltage supply. The electrical component supports 2 inputs. The transfer of data can be performed over 300MHz bandwidths.
74LVC1G3157GW,125 Features
2 Channels
Switch Circuit: SPDT
40μA Supply Current
Bandwidth: 300MHz
74LVC1G3157GW,125 Applications
There are a lot of Nexperia USA Inc. 74LVC1G3157GW,125 Analog Switches & Multiplexers ICs applications.
- Industrial control systems
- ISDN NT1/TA
- Power routing
- High reliability control systems
- E1 Multiplexer
- 65 V DACs
- Remote wireless modules
- Battery Powered Systems
- Communication systems
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads