74LVC1G384GW,125
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Contact Plating | Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 5-TSSOP, SC-70-5, SOT-353 |
| Number of Pins | 5 |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2010 |
| JESD-609 Code | e3 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 5 |
| Resistance | 15Ohm |
| Max Power Dissipation | 250mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 2.7V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | 74LVC1G384 |
| Pin Count | 5 |
| Operating Supply Voltage | 5V |
| Polarity | Non-Inverting |
| Number of Channels | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.65V |
| Operating Supply Current | 200μA |
| Nominal Supply Current | 100nA |
| Power Dissipation | 250mW |
| Max Supply Current | 200μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 10 ns |
| Number of Inputs | 1 |
| Supply Type | Single |
| Turn-Off Delay Time | 7.4 ns |
| -3db Bandwidth | 500MHz |
| On-State Resistance (Max) | 10Ohm |
| High Level Output Current | 50mA |
| Low Level Output Current | 50mA |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Current - Leakage (IS(off)) (Max) | 5μA |
| Channel Capacitance (CS(off), CD(off)) | 5pF |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 4.2ns, 5ns |
| Charge Injection | 7.5pC |
| Switch-on Time-Max | 8ns |
| Voltage - Supply, Single (V+) | 1.65V~5.5V |
| Length | 2mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
74LVC1G384GW,125 Overview
The electronic part can be shipped overseas conveniently because it is packaged in 5-TSSOP, SC-70-5, SOT-353. High reliability is achieved by using advanced packaging method Tape & Reel (TR). This analog switch is mounted in Surface Mount. 1:1 is the ratio of multiplexer to demultiplexer circuits. The operating temperature is extended to around -40°C~125°C TA. 5 terminations have been made so far. This electronic part offers high-quality output due to its 1 channels. Powered by a 2.7V voltage supply, the electrical part should be switched on and run. Into the electrical component body are injected 5 pins. SPST - NC switching circuits are used in these analog switch ics. Search with 74LVC1G384 if you are looking for analog multiplexer variants. This digital multiplexer has 15Ohm internal resistance. For details about the functions of 5 pins, please refer to the datasheets. normally, users should not supply switches with voltages higher than 5.5V. The digital multiplexer has a low cost Single supply. The lowest voltage the electronic part should receive is 1.65V. This multiplexer would work with 200μA current. Analogue multiplexers require a 1.65V~5.5V voltage to drain from a single voltage supply. If put voltage greater than 200μA on the device, damage may be caused to the analogue multiplexer. Operating voltages range from 5V. Operating 1 inputs is required.
74LVC1G384GW,125 Features
1 Channels
Switch Circuit: SPST - NC
200μA Supply Current
-3db Bandwidth: 500MHz
74LVC1G384GW,125 Applications
There are a lot of Nexperia USA Inc. 74LVC1G384GW,125 Analog Switches & Multiplexers ICs applications.
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- Imaging
- Fiber to the Home
- Central office
- Cell phones
- Microprocessor Controlled Analog Systems
- Remote Powered Equipment
- Channelized and Unchannelized DS3 applications
- Battery-powered systems
- PCMCIA cards
