74LVC1G53GS,115
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-XFDFN |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2014 |
| JESD-609 Code | e3 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| Resistance | 23Ohm |
| Terminal Finish | Tin (Sn) |
| Technology | CMOS |
| Terminal Position | DUAL |
| Number of Functions | 1 |
| Supply Voltage | 3.3V |
| Terminal Pitch | 0.35mm |
| Base Part Number | 74LVC1G53 |
| Pin Count | 8 |
| Number of Channels | 2 |
| Number of Circuits | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.65V |
| Power Dissipation | 250mW |
| Propagation Delay | 2.5 ns |
| Logic Function | Demultiplexer, Multiplexer |
| Supply Type | Single |
| -3db Bandwidth | 300MHz |
| On-State Resistance (Max) | 10Ohm |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 40 dB |
| Current - Leakage (IS(off)) (Max) | 5μA |
| Channel Capacitance (CS(off), CD(off)) | 6pF |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 3.8ns, 3.8ns |
| Charge Injection | 7.5pC |
| Voltage - Supply, Single (V+) | 1.65V~5.5V |
| Height Seated (Max) | 0.35mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
74LVC1G53GS,115 Overview
Due to its 8-XFDFN packaging, the electronic part is convenient for international shipping. This high-reliability packaging method uses advanced packaging methods Tape & Reel (TR). The multiplexer is located in Surface Mount. Multiplexer and demultiplexer circuits have a number 2:1. Operational temperature extended around -40°C~125°C TA. Total terminations are 8. Due to its 2 channels, the electrical component produces high-quality output. In the case of a voltage supply of 3.3V volts, the electrical part can be powered up and run. A total of 8 pins are injected into the electrical part body. Multiplexers built on a SPDT switching circuit are built. Circuits number 1 make up this analogue multiplexer. Try searching with 74LVC1G53 to find analog multiplexer variants. A 23Ohm internal resistance characterizes this multiplexer. For functions related to 8 pins, please refer to the datasheets. normally, users should not supply switches with voltages higher than 5.5V. A analog switch ic that has a cost-effective Single supply type. There should be 1.65V voltage fed to the electrical part below 1.65V. This analog switch requires a voltage of 1.65V~5.5V to drain from a single voltage supply.
74LVC1G53GS,115 Features
2 Channels
Switch Circuit: SPDT
-3db Bandwidth: 300MHz
74LVC1G53GS,115 Applications
There are a lot of Nexperia USA Inc. 74LVC1G53GS,115 Analog Switches & Multiplexers ICs applications.
- Fiber In The Loop (FITL)
- Cell phones
- Intelligent PBX
- FTTH
- ISDN NT1/TA
- Transmit
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- SDH/SONET multiplexers
- Power routing
- SONET
