74LVC1G66GV,125
| Parameters | |
|---|---|
| High Level Output Current | 50mA |
| Low Level Output Current | 50mA |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Current - Leakage (IS(off)) (Max) | 5μA |
| Channel Capacitance (CS(off), CD(off)) | 6.5pF |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 4.2ns, 5ns |
| Charge Injection | 7.5pC |
| Voltage - Supply, Single (V+) | 1.65V~5.5V |
| Length | 2.9mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Contact Plating | Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | SC-74A, SOT-753 |
| Number of Pins | 5 |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2005 |
| JESD-609 Code | e3 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 5 |
| Resistance | 15Ohm |
| Max Power Dissipation | 250mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 2.7V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | 74LVC1G66 |
| Pin Count | 5 |
| Operating Supply Voltage | 5V |
| Polarity | Non-Inverting |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.65V |
| Operating Supply Current | 200μA |
| Number of Ports | 2 |
| Nominal Supply Current | 100nA |
| Power Dissipation | 250mW |
| Max Supply Current | 200μA |
| Number of Bits | 1 |
| Throw Configuration | SPST |
| Turn On Delay Time | 5.3 ns |
| Family | LVC/LCX/Z |
| Number of Inputs | 1 |
| Output Characteristics | 3-STATE |
| Supply Type | Single |
| Turn-Off Delay Time | 4.2 ns |
| Logic IC Type | BUS DRIVER |
| -3db Bandwidth | 500MHz |
| On-State Resistance (Max) | 10Ohm |
74LVC1G66GV,125 Overview
The electronic component is convenient to ship overseas because it is packed in a SC-74A, SOT-753. The advanced packaging method Tape & Reel (TR) provides high reliability. This analog switch is mounted in Surface Mount. Multiplexers and demultiplexers have the same number of circuits 1:1. The operating temperature is extended to around -40°C~125°C TA. There are 5 terminations totally. An 2.7V voltage supply should allow the electrical part to be turned on and run. This electronic part can be found in the 5 series. SPST - NO switching circuits are used in these analog switch ics. Using the 74LVC1G66 search parameter, you can discover variants of the switch. There is 15Ohm internal resistance in this digital multiplexer. To find out what the functions of 5 pins are, please refer to their datasheets. A voltage higher than 5.5V should not normally be supplied to the switches. Analogue multiplexers of the Single supply type that are cost-effective. The lowest voltage fed to the electronic component should be 1.65V. For this multiplexer to operate, 200μA current would be sufficient. Using a single voltage supply, this switch device consumes 1.65V~5.5V volts. Putting voltage greater than 200μA on the multiplexer may cause damage. 5V operating voltages are supported by the electronic component. Among the inputs that can be operated are the 1 inputs. The switch device is capable of conducting in a 1-bit mode.
74LVC1G66GV,125 Features
Switch Circuit: SPST - NO
200μA Supply Current
-3db Bandwidth: 500MHz
1-Bit
74LVC1G66GV,125 Applications
There are a lot of Nexperia USA Inc. 74LVC1G66GV,125 Analog Switches & Multiplexers ICs applications.
- Medical Instrumentation
- High-Voltage
- PDH Multiplexers
- Multiplexers
- Low-Voltage
- USB 1.1 signal switching circuits
- Industrial control systems
- DSUs
- PBX interfaces
- Optical Applications
