74LVC2G53GD,125
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-XFDFN |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| Resistance | 15Ohm |
| Terminal Finish | NICKEL PALLADIUM GOLD |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 250mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 2.7V |
| Terminal Pitch | 0.5mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | 74LVC2G53 |
| Pin Count | 8 |
| Power Supplies | 3.3V |
| Number of Channels | 2 |
| Number of Circuits | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.65V |
| Operating Supply Current | 40μA |
| Power Dissipation | 250mW |
| Propagation Delay | 800 ps |
| Turn On Delay Time | 6.7 ns |
| Logic Function | Demultiplexer, Multiplexer |
| Supply Type | Single |
| Bandwidth | 300MHz |
| Supply Current-Max (Isup) | 0.04mA |
| Turn-Off Delay Time | 6.8 ns |
| On-State Resistance (Max) | 10Ohm |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 40 dB |
| Current - Leakage (IS(off)) (Max) | 5μA |
| Channel Capacitance (CS(off), CD(off)) | 6pF |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 3.8ns, 3.8ns |
| Charge Injection | 7.5pC |
| Switching | BREAK-BEFORE-MAKE |
| Voltage - Supply, Single (V+) | 1.65V~5.5V |
| Signal Current-Max | 0.05A |
| Height Seated (Max) | 0.5mm |
| Length | 3mm |
| Radiation Hardening | No |
| RoHS Status | RoHS Compliant |
74LVC2G53GD,125 Overview
Presented in 8-XFDFN, this electrical component is convenient for overseas shipping. The advanced packaging method Tape & Reel (TR) provides high reliability. This analog switch is mounted in Surface Mount. 2:1 is the ratio between multiplexers and demultiplexers. Temperatures around -40°C~125°C TA are extended for operation. In total, there have been 8 terminations. As a result of its 2 channels, this electronic component provides high-quality output. Powered by a 2.7V voltage supply, the electrical part should be switched on and run. The electronic part body is injected with 8 pins. A SPDT switching circuit is used to build these analog multiplexers. A total of 1 circuits make up this switch device. Try searching for the analog switch ic with 74LVC2G53 if you are looking for variants. As far as internal resistance is concerned, it has 15Ohm. To find out what the functions of 8 pins are, please refer to their datasheets. The analogue multiplexer in this example is a typical Multiplexer or Switches. An abnormal situation would be for the switch device to be supplied with a voltage greater than 5.5V. A cost-effective Single supply type analogue multiplexer. The lowest voltage the electronic part should receive is 1.65V. This digital switch can be operated with a current of 40μA. This analog switch requires a voltage of 1.65V~5.5V to drain from a single voltage supply. A 300MHz-bandwidth can be used for data transfer.
74LVC2G53GD,125 Features
2 Channels
Switch Circuit: SPDT
40μA Supply Current
Bandwidth: 300MHz
74LVC2G53GD,125 Applications
There are a lot of Nexperia USA Inc. 74LVC2G53GD,125 Analog Switches & Multiplexers ICs applications.
- Intelligent PBX
- DSUs
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- Fault Tolerant Systems
- Transmit
- Power routing
- Microprocessor Controlled Analog Systems
- New designs requiring multiplexer functions
- Switching Systems
- E1 Multiplexer
