74LVC2G66DC-Q100H

3.9ns, 5ns SPST - NO 10Ohm DUAL Analog Switches 74LVC2G66 8 Pins 5μA 3.3V 8-VFSOP (0.091, 2.30mm Width)

Manufacturer: Nexperia USA Inc.
Nocochips NO: 554-74LVC2G66DC-Q100H
Package: 8-VFSOP (0.091, 2.30mm Width)
Datasheet: PDF
Stock: 169
Description: 3.9ns, 5ns SPST - NO 10Ohm DUAL Analog Switches 74LVC2G66 8 Pins 5μA 3.3V 8-VFSOP (0.091, 2.30mm Width)(Kg)

Details

Tags

Parameters
Nominal Supply Current	100nA
Max Supply Current	200μA
Throw Configuration	SPST
Supply Type	Single
-3db Bandwidth	500MHz
On-State Resistance (Max)	10Ohm
Multiplexer/Demultiplexer Circuit	1:1
Off-state Isolation-Nom	37 dB
Current - Leakage (IS(off)) (Max)	5μA
Channel Capacitance (CS(off), CD(off))	5pF
Switch Circuit	SPST - NO
Switch Time (Ton, Toff) (Max)	3.9ns, 5ns
Charge Injection	7.5pC
Crosstalk	-56dB @ 1MHz
Switch-on Time-Max	13ns
Switch-off Time-Max	11.5ns
Voltage - Supply, Single (V+)	1.65V~5.5V
Height Seated (Max)	1mm
Radiation Hardening	No
RoHS Status	ROHS3 Compliant
Factory Lead Time	1 Week
Mount	Surface Mount
Mounting Type	Surface Mount
Package / Case	8-VFSOP (0.091, 2.30mm Width)
Number of Pins	8
Operating Temperature	-40°C~125°C TA
Packaging	Tape & Reel (TR)
Series	Automotive, AEC-Q100
Part Status	Active
Moisture Sensitivity Level (MSL)	1 (Unlimited)
Number of Terminations	8
Resistance	15Ohm
Max Power Dissipation	250mW
Technology	CMOS
Terminal Position	DUAL
Terminal Form	GULL WING
Number of Functions	2
Supply Voltage	3.3V
Terminal Pitch	0.5mm
Base Part Number	74LVC2G66
Pin Count	8
Number of Channels	1
Number of Circuits	2
Max Supply Voltage	5.5V
Min Supply Voltage	1.65V
Operating Supply Current	200μA

74LVC2G66DC-Q100H Overview

Shipping overseas is convenient due to the electrical component's packing in 8-VFSOP (0.091, 2.30mm Width). High reliability is ensured by the advanced packaging method Tape & Reel (TR). Surface Mount is where this multiplexer is located. 1:1 is the ratio of multiplexer to demultiplexer circuits. Operating temperature around -40°C~125°C TA extended. Total terminations are 8. By its 1 channels, the electronic component provides high-quality output. Powered by a 3.3V voltage supply, the electrical part should be switched on and run. As part of its design, the 8 series is equipped with this electronic component. A SPST - NO switching circuit is used for these analog switches. It consists of 2 circuits. Try searching with 74LVC2G66 to find analog multiplexer variants. In this multiplexer, the internal resistance is 15Ohm. Datasheets for functions of 8 pins are available. A voltage higher than 5.5V should not normally be supplied to the switches. The digital multiplexer has a low cost Single supply. It is recommended that the electrical component receives a voltage of 1.65V. An operating current of 200μA would be sufficient for this switch device. Using only a single voltage supply, this analog switch requires 1.65V~5.5V voltage. A digital multiplexer may suffer damage if voltage is applied above 200μA. The Automotive, AEC-Q100 series contains it.