74LVC2G66DC,125
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-VFSOP (0.091, 2.30mm Width) |
| Number of Pins | 8 |
| Weight | 29.993795mg |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| Resistance | 15Ohm |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Max Power Dissipation | 250mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 2.7V |
| Terminal Pitch | 0.5mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | 74LVC2G66 |
| Pin Count | 8 |
| Number of Channels | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.65V |
| Operating Supply Current | 200μA |
| Power Dissipation | 250mW |
| Max Supply Current | 200μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 5 ns |
| Number of Inputs | 2 |
| Supply Type | Single |
| Turn-Off Delay Time | 6.5 ns |
| -3db Bandwidth | 500MHz |
| On-State Resistance (Max) | 10Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 46 dB |
| Current - Leakage (IS(off)) (Max) | 5μA |
| Channel Capacitance (CS(off), CD(off)) | 5pF |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 3.9ns, 5ns |
| Charge Injection | 7.5pC |
| Crosstalk | -56dB @ 1MHz |
| Switch-on Time-Max | 13ns |
| Voltage - Supply, Single (V+) | 1.65V~5.5V |
| Drain to Source Resistance | 195Ohm |
| Height Seated (Max) | 1mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
74LVC2G66DC,125 Overview
Due to its 8-VFSOP (0.091, 2.30mm Width) packaging, the electronic part is convenient for international shipping. This packaging method provides high reliability because it uses advanced packaging techniques. It is mounted in the position Surface Mount. In the multiplexer and demultiplexer, 1:1 represents the number of circuits. Operation at a temperature around -40°C~125°C TA. In total, there are 8 terminations. The electronic part delivers high-quality output through its 1 channels. It is safe to turn on and run the electronic component with a 2.7V voltage supply. Electronic part bodies are injected with 8 pins. Unlike digital switches, these are based on SPST - NO switching circuits. 74LVC2G66 can be used to search for analog multiplexer variants. There is 15Ohm internal resistance in this digital multiplexer. The functions of 8 pins can be found in the datasheets. Users shouldn't supply more than 5.5V voltage to the switch device. Analog switch ics with Single supply type are cost-effective. It is recommended to use 1.65V as the lowest voltage for the electrical part. In order to operate this switch device, it would need a current of 200μA. Using a single voltage supply, this switch device consumes 1.65V~5.5V volts. A voltage higher than 200μA may cause damage to the switch multiplexer. In order to operate the 2 inputs, there are several steps to follow. Drain to Source resistance is 195Ohm.
74LVC2G66DC,125 Features
1 Channels
Switch Circuit: SPST - NO
200μA Supply Current
-3db Bandwidth: 500MHz
Drain-to-Source resistance: 195Ohm
74LVC2G66DC,125 Applications
There are a lot of Nexperia USA Inc. 74LVC2G66DC,125 Analog Switches & Multiplexers ICs applications.
- Digital access cross connects
- Precision instrumentation
- Cable Telephony – NIU, Set-Top Box, Home Side Box
- Channel Banks
- FTTH
- Cross Connects
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- Power routing
- Fiber In The Loop (FITL)
- High reliability control systems
