74LVC2G66DP,125
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| Resistance | 500mOhm |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Max Power Dissipation | 250mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 2.7V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | 74LVC2G66 |
| Pin Count | 8 |
| Operating Supply Voltage | 5V |
| Number of Channels | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.65V |
| Operating Supply Current | 150nA |
| Nominal Supply Current | 100nA |
| Power Dissipation | 250mW |
| Max Supply Current | 200μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 4.6 ns |
| Number of Inputs | 2 |
| Supply Type | Single |
| Turn-Off Delay Time | 3.8 ns |
| -3db Bandwidth | 500MHz |
| On-State Resistance (Max) | 10Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 46 dB |
| Current - Leakage (IS(off)) (Max) | 5μA |
| Channel Capacitance (CS(off), CD(off)) | 5pF |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 3.9ns, 5ns |
| Charge Injection | 7.5pC |
| Crosstalk | -56dB @ 1MHz |
| Switch-on Time-Max | 13ns |
| Switch-off Time-Max | 11.5ns |
| Voltage - Supply, Single (V+) | 1.65V~5.5V |
| Drain to Source Resistance | 195Ohm |
| Height Seated (Max) | 1.1mm |
| Length | 3mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
74LVC2G66DP,125 Overview
The electronic part can be shipped overseas conveniently because it is packaged in 8-TSSOP, 8-MSOP (0.118, 3.00mm Width). The advanced packaging method Tape & Reel (TR) provides high reliability. The multiplexer is located in Surface Mount. 1:1 is the ratio of multiplexer to demultiplexer circuits. Operating temperature around -40°C~125°C TA extended. Total terminations are 8. A 1 channel electronic part produces high-quality output. With a 2.7V voltage supply, the electrical component should be turned on and run. A total of 8 pins are injected into the body of the electronic part. The analog switch ics are built using SPST - NO switching circuits. Use 74LVC2G66 to search for variants of the digital switches. As far as internal resistance is concerned, it has 500mOhm. For details about the functions of 8 pins, please refer to the datasheets. A voltage higher than 5.5V should not normally be supplied to the switches. Analog switch ics with Single supply type are cost-effective. The lowest voltage fed to the electronic component should be 1.65V. It would be sufficient to run this analogue multiplexer with 150nA current. This analog switch requires a voltage of 1.65V~5.5V to drain from a single voltage supply. If put voltage greater than 200μA on the device, damage may be caused to the analogue multiplexer. This electrical part is compatible with 5V operating voltages. There are 2 inputs to be operated. Resistivity from Drain to Source is 195Ohm for this electronic part.
74LVC2G66DP,125 Features
1 Channels
Switch Circuit: SPST - NO
150nA Supply Current
-3db Bandwidth: 500MHz
Drain-to-Source resistance: 195Ohm
74LVC2G66DP,125 Applications
There are a lot of Nexperia USA Inc. 74LVC2G66DP,125 Analog Switches & Multiplexers ICs applications.
- Industrial and process control systems
- Intelligent PBX
- Public switching systems
- Medical
- Precision instrumentation
- Data Acquisition Systems
- Industrial control systems
- Fiber In The Loop (FITL)
- Residential Gateways, Home Gateway/Router
- PDH Multiplexers
