74LVC2G66GT,115
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-XFDFN |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e3 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| Resistance | 15Ohm |
| Terminal Finish | Tin (Sn) |
| Max Power Dissipation | 250mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 2.7V |
| Terminal Pitch | 0.5mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | 74LVC2G66 |
| Pin Count | 8 |
| Operating Supply Voltage | 5V |
| Number of Channels | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.65V |
| Operating Supply Current | 200μA |
| Nominal Supply Current | 100nA |
| Power Dissipation | 250mW |
| Max Supply Current | 200μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 4.6 ns |
| Number of Inputs | 2 |
| Supply Type | Single |
| Turn-Off Delay Time | 3.8 ns |
| -3db Bandwidth | 500MHz |
| On-State Resistance (Max) | 10Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 46 dB |
| Current - Leakage (IS(off)) (Max) | 5μA |
| Channel Capacitance (CS(off), CD(off)) | 5pF |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 3.9ns, 5ns |
| Charge Injection | 7.5pC |
| Crosstalk | -56dB @ 1MHz |
| Switch-on Time-Max | 13ns |
| Switch-off Time-Max | 11.5ns |
| Voltage - Supply, Single (V+) | 1.65V~5.5V |
| Height Seated (Max) | 0.5mm |
| Length | 1.95mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
74LVC2G66GT,115 Overview
This electronic part is conveniently packaged in 8-XFDFN, making it easy to ship abroad. This packaging method provides high reliability because it uses advanced packaging techniques. In Surface Mount, you'll find this switch device. The ratio between the number of multiplexer and demultiplexer circuits is 1:1. Increasing operating temperature to around -40°C~125°C TA. 8 terminations have been made so far. By its 1 channels, the electronic component provides high-quality output. When a voltage supply of 2.7V is used, the electronic component should be turned on and run. It is part of the design of the 8 series that this electronic component is included. Circuits based on SPST - NO switching are used to construct these analog switch ics. Search with 74LVC2G66 if you are looking for analog multiplexer variants. The internal resistance of this digital multiplexer is 15Ohm. Please refer to the datasheets for 8 pins functions. Multiplexers should not be powered above 5.5V in normal situations. Single supply type digital switch with a low cost. 1.65V should be the lowest voltage fed to the electronic component. For this multiplexer to operate, 200μA current would be sufficient. This analogue multiplexer requires a voltage of 1.65V~5.5V when it drains from a single voltage supply. Putting voltage greater than 200μA on the multiplexer may cause damage. 5V operating voltages can be used with this electrical part. It is possible to operate 2 inputs.
74LVC2G66GT,115 Features
1 Channels
Switch Circuit: SPST - NO
200μA Supply Current
-3db Bandwidth: 500MHz
74LVC2G66GT,115 Applications
There are a lot of Nexperia USA Inc. 74LVC2G66GT,115 Analog Switches & Multiplexers ICs applications.
- Access Concentrators
- Video switching
- Microwave transmission systems
- ISDN NT1/TA
- Digital Cross-Connects
- Medical
- Communication systems
- Audio signal routing
- Digital cross connects (DSX-1)
- Fiber In The Loop (FITL)
