74LVC4066BQ,115
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 14-VFQFN Exposed Pad |
| Number of Pins | 14 |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| Resistance | 15Ohm |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Max Power Dissipation | 500mW |
| Technology | CMOS |
| Terminal Position | QUAD |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 2.7V |
| Terminal Pitch | 0.5mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | 74LVC4066 |
| Pin Count | 14 |
| Operating Supply Voltage | 5V |
| Number of Channels | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.65V |
| Operating Supply Current | 40μA |
| Nominal Supply Current | 100nA |
| Power Dissipation | 500mW |
| Max Supply Current | 40μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 5.3 ns |
| Number of Inputs | 4 |
| Supply Type | Single |
| Turn-Off Delay Time | 4.2 ns |
| -3db Bandwidth | 500MHz |
| On-State Resistance (Max) | 10Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 42 dB |
| Current - Leakage (IS(off)) (Max) | 5μA |
| Channel Capacitance (CS(off), CD(off)) | 8pF |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 3.9ns, 5ns |
| Charge Injection | 7.5pC |
| Crosstalk | -56dB @ 1MHz |
| Switch-on Time-Max | 6.5ns |
| Switch-off Time-Max | 8.5ns |
| Voltage - Supply, Single (V+) | 1.65V~5.5V |
| Height | 950μm |
| Length | 3.1mm |
| Width | 2.6mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
74LVC4066BQ,115 Overview
Due to its 14-VFQFN Exposed Pad packaging, the electronic part is convenient for international shipping. High reliability is ensured by the advanced packaging method Tape & Reel (TR). There is an analog multiplexer mounted in position Surface Mount. There is 1:1 ratio between the number of multiplexers and demultiplexers. Operating temperature around -40°C~125°C TA extended. In total, 14 terminations have occurred. This electronic part offers high-quality output due to its 1 channels. A 2.7V voltage supply should turn on and run the electronic component. Into the electrical component body are injected 14 pins. These analog multiplexers are built based on SPST - NO switching circuits. Try searching for the analog switch ic with 74LVC4066 if you are looking for variants. It has an internal resistance of 15Ohm. For functions related to 14 pins, please refer to the datasheets. In normalcircumstances, users should not exceed 5.5V volts for the multiplexer. Analogue multiplexer with a Single supply type that is cost-effective. It is recommended to use 1.65V as the lowest voltage for the electrical part. It would be sufficient to run this analogue multiplexer with 40μA current. An analogue multiplexer drains from a single voltage supply at 1.65V~5.5V. A voltage higher than 40μA may cause damage to the switch multiplexer. It can operate from 5V operating voltages. The electrical component supports 4 inputs.
74LVC4066BQ,115 Features
1 Channels
Switch Circuit: SPST - NO
40μA Supply Current
-3db Bandwidth: 500MHz
74LVC4066BQ,115 Applications
There are a lot of Nexperia USA Inc. 74LVC4066BQ,115 Analog Switches & Multiplexers ICs applications.
- Communication systems
- Voice over IP/DSL – Integrated Access Devices, Smart
- Digital cross connects (DSX-1)
- High speed data transmission line cards
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- HDTV
- Data switching
- Frame Relay Equipment
- Multiplexers
