74V1G66CTR
| Parameters | |
|---|---|
| Contact Plating | Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 5-TSSOP, SC-70-5, SOT-353 |
| Number of Pins | 5 |
| Operating Temperature | -55°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 5 |
| Termination | SMD/SMT |
| Resistance | 10Ohm |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 3.3V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | 74V1G66 |
| Pin Count | 5 |
| Polarity | Non-Inverting |
| Number of Channels | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 2V |
| Output Current | 50mA |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 4 ns |
| Supply Type | Single |
| Turn-Off Delay Time | 7.5 ns |
| -3db Bandwidth | 180MHz |
| On-State Resistance (Max) | 10Ohm |
| High Level Output Current | 50mA |
| Low Level Output Current | 50mA |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 60 dB |
| Current - Leakage (IS(off)) (Max) | 100nA |
| Channel Capacitance (CS(off), CD(off)) | 3pF |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 4ns, 7.5ns |
| Voltage - Supply, Single (V+) | 2V~5.5V |
| Normal Position | NO |
| Length | 2mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
74V1G66CTR Overview
The electronic part can be shipped overseas conveniently because it is packaged in 5-TSSOP, SC-70-5, SOT-353. The advanced packaging method Tape & Reel (TR) provides high reliability. In Surface Mount, you'll find this switch device. There is 1:1 ratio between the number of multiplexers and demultiplexers. The operating temperature is extended to around -55°C~125°C TA. There are 5 terminations totally. The electronic part provides high-quality output because it has 1 channels. If the voltage supply is 3.3V volts, the electrical component should be turned on and run. 5 pins are injected to the electronic part body. Circuits based on SPST - NO switching are used to construct these analog switch ics. If you are looking for variants of the digital switch, trying search with 74V1G66. Analog switches have 10Ohm internal resistance. The datasheets for the 5 pins explain the functions. This switch device is a typical Multiplexer or Switches. In a normalsituation, users should not supply the switches with voltage higher than 5.5V. The digital multiplexer has a low cost Single supply. 2V is the lowest voltage that should be fed to the electronic electronic part. Analogue multiplexers require a 2V~5.5V voltage to drain from a single voltage supply. Putting voltage greater than 1μA on the multiplexer may cause damage.
74V1G66CTR Features
1 Channels
Switch Circuit: SPST - NO
-3db Bandwidth: 180MHz
74V1G66CTR Applications
There are a lot of STMicroelectronics 74V1G66CTR Analog Switches & Multiplexers ICs applications.
- Communication systems
- PDH Multiplexers
- Wireless Local Loop
- SDH
- Battery Powered Systems
- USB 1.1 signal switching circuits
- Switching Systems
- ATM
- Avionics
- Optical Applications
