74VHC112MTCX
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 4 days ago) |
| Contact Plating | Gold |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 16 |
| Weight | 173mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2007 |
| Series | 74VHC |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Type | JK Type |
| Subcategory | FF/Latches |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Voltage - Supply | 2V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Supply Voltage | 3.3V |
| Base Part Number | 74VHC112 |
| Function | Set(Preset) and Reset |
| Output Type | Differential |
| Polarity | Non-Inverting |
| Supply Voltage-Min (Vsup) | 2V |
| Number of Circuits | 2 |
| Clock Frequency | 185MHz |
| Propagation Delay | 10.5 ns |
| Quiescent Current | 2μA |
| Turn On Delay Time | 16.5 ns |
| Family | AHC/VHC |
| Logic Function | AND, Flip-Flop, JK-Type |
| Current - Output High, Low | 8mA 8mA |
| Max I(ol) | 0.008 A |
| Number of Bits per Element | 1 |
| Max Propagation Delay @ V, Max CL | 10.5ns @ 5V, 50pF |
| Trigger Type | Negative Edge |
| Input Capacitance | 4pF |
| Number of Input Lines | 5 |
| Clock Edge Trigger Type | Negative Edge |
| Width | 4.4mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
74VHC112MTCX Overview
The item is packaged in 16-TSSOP (0.173, 4.40mm Width)cases. It is included in the package Tape & Reel (TR). T flip flop is configured with an output of Differential. It is configured with a trigger that uses Negative Edge. It is mounted in the way of Surface Mount. The supply voltage is set to 2V~5.5V. It is at -40°C~85°C TAdegrees Celsius that the system is operating. Logic flip flops of this type are classified as JK Type. In FPGA terms, D flip flop is a type of 74VHCseries FPGA. Its output frequency should not exceed 185MHz. A total of 16 terminations have been made. This D latch belongs to the family of 74VHC112. The power supply voltage is 3.3V. The input capacitance of this T flip flop is 4pF farads, which is defined as the capacitance between the input terminals of an op amp with either input grounded. An electronic device belonging to the family AHC/VHCcan be found here. Electronic part Surface Mountis mounted in the way. The 16pins are designed into the board. This device has the clock edge trigger type of Negative Edge. The RS flip flops belongs to FF/Latches base part number. For normal operation, the supply voltage (Vsup) should be above 2V. The superior flexibility of this product is achieved by using 2 circuits. As a result of its reliable performance, this T flip flop is suitable for TAPE AND REEL. This input has 5lines. As a result, it consumes 2μA of quiescent current without being affected by external factors.
74VHC112MTCX Features
Tape & Reel (TR) package
74VHC series
16 pins
74VHC112MTCX Applications
There are a lot of ON Semiconductor 74VHC112MTCX Flip Flops applications.
- ESD performance
- ESD protection
- Matched Rise and Fall
- Frequency Divider circuits
- 2 – Bit synchronous counter
- Common Clocks
- Guaranteed simultaneous switching noise level
- Communications
- Shift registers
- Dynamic threshold performance
