74VHC4053N
| Parameters | |
|---|---|
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 16-DIP (0.300, 7.62mm) |
| Number of Pins | 16 |
| Supplier Device Package | 16-PDIP |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Resistance | 100Ohm |
| Max Operating Temperature | 85°C |
| Min Operating Temperature | -40°C |
| Max Power Dissipation | 600mW |
| Base Part Number | 74VHC4053 |
| Number of Outputs | 3 |
| Number of Channels | 3 |
| Number of Circuits | 3 |
| Max Supply Voltage | 6V |
| Min Supply Voltage | 2V |
| Power Dissipation | 600mW |
| Throw Configuration | SPDT |
| Propagation Delay | 35 ns |
| Turn On Delay Time | 200 ns |
| Logic Function | Demultiplexer, Multiplexer |
| Number of Inputs | 6 |
| Voltage - Supply, Single/Dual (±) | 2V~6V ±1V~6V |
| Supply Type | Dual, Single |
| Bandwidth | 30MHz |
| Turn-Off Delay Time | 170 ns |
| Max Dual Supply Voltage | 6V |
| On-State Resistance (Max) | 100Ohm |
| Min Dual Supply Voltage | 1V |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Current - Leakage (IS(off)) (Max) | 50nA |
| Channel Capacitance (CS(off), CD(off)) | 5pF 30pF |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 41ns, 32ns |
| Channel-to-Channel Matching (ΔRon) | 10Ohm |
| Crosstalk | -50dB @ 1MHz |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
74VHC4053N Overview
As the electronic part is packed in 16-DIP (0.300, 7.62mm), international shipping is convenient. The advanced packaging method Tube provides high reliability. A switch device like this is mounted in Through Hole. 2:1 is the ratio between multiplexers and demultiplexers. Around -40°C~85°C TA is the extended operating temperature. By its 3 channels, the electronic component provides high-quality output. These analog multiplexers are built based on SPDT switching circuits. 3 circuits are used in this analogue multiplexer. Try searching with 74VHC4053 if you're looking for variants. An switch multiplexer with 100Ohm internal resistance has a value of 100Ohm. For details about the functions of 16 pins, please refer to the datasheets. It is normally recommended that users do not supply the multiplexer with voltages higher than 6V. The digital multiplexer has a low cost Dual, Single supply. In order for the electronic part to function properly, the lowest voltage should be 2V. For this multiplexer, dual supply voltage is feasible, but it should not exceed 6V. If you are using dual power supplies, you should attach at least 1V. It is possible to operate 6 inputs. There are 30MHz bandwidths for data transfer. Temperatures above 85°C should not be used to operate the switches. In this digital multiplexer, there are 3 outputs. It is possible to purchase a 16-PDIP package from suppliers.
74VHC4053N Features
3 Channels
Switch Circuit: SPDT
Bandwidth: 30MHz
74VHC4053N Applications
There are a lot of ON Semiconductor 74VHC4053N Analog Switches & Multiplexers ICs applications.
- Remote wireless modules
- Communication systems
- Microprocessor Controlled Analog Systems
- PDAs
- Wireless Local Loop
- Fault Tolerant Systems
- Channel Banks
- Video signal routing
- Avionics and Military Systems
- DSUs
