74VHC4066M
| Parameters | |
|---|---|
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Resistance | 70Ohm |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Max Power Dissipation | 500mW |
| Peak Reflow Temperature (Cel) | NOT SPECIFIED |
| Reach Compliance Code | unknown |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | 74VHC4066 |
| Max Supply Voltage | 12V |
| Min Supply Voltage | 2V |
| Power Dissipation | 500mW |
| Output Current | 25mA |
| Max Supply Current | 4μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 85 ns |
| Supply Type | Single |
| Turn-Off Delay Time | 100 ns |
| Number of Gates | 4 |
| -3db Bandwidth | 100MHz |
| On-State Resistance (Max) | 70Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Current - Leakage (IS(off)) (Max) | 100nA |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 10ns, 30ns |
| Channel-to-Channel Matching (ΔRon) | 5 Ω |
| Crosstalk | -50dB @ 1MHz |
| Voltage - Supply, Single (V+) | 2V~12V |
| REACH SVHC | No SVHC |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 14-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 14 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2005 |
| JESD-609 Code | e4 |
| Part Status | Obsolete |
74VHC4066M Overview
The electronic component is convenient to ship overseas because it is packed in a 14-SOIC (0.154, 3.90mm Width). High reliability is provided by advanced packaging method Tube. Surface Mount is where this multiplexer is located. In the multiplexer and demultiplexer, 1:1 represents the number of circuits. An extended operating temperature of -40°C~85°C TA degrees Celsius. A SPST - NO switching circuit is used to build these analog multiplexers. Look for analog switch ic variants by searching with 74VHC4066. As far as internal resistance is concerned, it has 70Ohm. The datasheets for the 14 pins explain the functions. It is generally not recommended to supply a voltage higher than 12V to the switch device in normal circumstances. A analog switch ic that has a cost-effective Single supply type. It is recommended that the electrical component receives a voltage of 2V. Analogue multiplexers require a 2V~12V voltage to drain from a single voltage supply. Putting voltage greater than 4μA on the multiplexer may cause damage.
74VHC4066M Features
Switch Circuit: SPST - NO
-3db Bandwidth: 100MHz
74VHC4066M Applications
There are a lot of ON Semiconductor 74VHC4066M Analog Switches & Multiplexers ICs applications.
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- PDH Multiplexers
- Video signal routing
- CSU
- DSLAMs
- SONET/SDH ADM
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- Access Concentrators
- Frame Relay Equipment
- Battery Powered Instruments
