8100604EA
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Contact Plating | Lead, Tin |
| Mount | Through Hole |
| Package / Case | CDIP |
| Number of Pins | 16 |
| Operating Temperature | 0°C~70°C TA |
| Published | 2003 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 75Ohm |
| Terminal Finish | Tin/Lead (Sn/Pb) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 800mW |
| Technology | CMOS |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 2 |
| Supply Voltage | 15V |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Power Supplies | 5+-15V |
| Number of Channels | 2 |
| Number of Circuits | 2 |
| Max Supply Voltage | 18V |
| Min Supply Voltage | 4.5V |
| Analog IC - Other Type | DPST |
| Nominal Supply Current | 30mA |
| Max Supply Current | 30mA |
| Turn On Delay Time | 400 ns |
| Supply Type | Dual |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 200 ns |
| Max Dual Supply Voltage | 18V |
| On-State Resistance (Max) | 80Ohm |
| Min Dual Supply Voltage | 4.5V |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Current - Leakage (IS(off)) (Max) | 5nA |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 400ns, 200ns |
| Channel-to-Channel Matching (ΔRon) | 5 Ω |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 375ns |
| Voltage - Supply, Dual (V±) | ±4.5V~18V |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
8100604EA Overview
As the electronic part is packed in CDIP, international shipping is convenient. 2:1 is the ratio of multiplexer to demultiplexer circuits. Increasing operating temperature to around 0°C~70°C TA. There are 16 terminations totally. The electronic part delivers high-quality output through its 2 channels. It is safe to turn on and run the electronic component with a 15V voltage supply. As part of its design, the 16 series is equipped with this electronic component. SPDT switching circuits are used in these analog switch ics. 2 circuits are used in this analogue multiplexer. It has an internal resistance of 75Ohm. You can find the functions of the 16 pins in the datasheets. Multiplexer or Switches is a typical switch device. Users shouldn't supply more than 18V voltage to the switch device. The analog switch ic is of the Dual supply type and is cost-effective. 4.5V is the lowest voltage the electrical component should receive. The analogue multiplexer may be damaged if voltage is greater than 30mA. Dual supply volatge is feasible for this multiplexer. But it should not go beyond 18V. For dual power supplies, a voltage of at least 4.5V should be attached. It is integrated with DPST analog ICs. It is possible to use SEPARATE OUTPUT outputs on this digital multiplexer.
8100604EA Features
2 Channels
Switch Circuit: SPDT
8100604EA Applications
There are a lot of Maxim Integrated 8100604EA Analog Switches & Multiplexers ICs applications.
- Relay replacements
- Digital Cross-Connects
- ADCs such as AD7840/8, AD7870/1/2/4/5/6/8
- Switching Systems
- Communications systems
- Multiplexers
- HDTV
- Communication systems
- Imaging
- Ultrasound
