9204201EA
| Parameters | |
|---|---|
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 16-CDIP (0.300, 7.62mm) |
| Operating Temperature | -55°C~125°C TA |
| Packaging | Bulk |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Max Power Dissipation | 900mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | NOT SPECIFIED |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Terminal Pitch | 2.54mm |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Pin Count | 16 |
| Number of Channels | 8 |
| Number of Circuits | 1 |
| Max Supply Voltage | 44V |
| Min Supply Voltage | 13V |
| Analog IC - Other Type | SINGLE-ENDED MULTIPLEXER |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 100Ohm |
| Min Dual Supply Voltage | 5V |
| High Level Output Current | 30mA |
| Multiplexer/Demultiplexer Circuit | 8:1 |
| Off-state Isolation-Nom | 75 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 3pF 26pF |
| On-state Resistance Match-Nom | 15Ohm |
| Switch Time (Ton, Toff) (Max) | 150ns, 150ns |
| Charge Injection | 20pC |
| Channel-to-Channel Matching (ΔRon) | 15 Ω (Max) |
| Switch-on Time-Max | 225ns |
| Voltage - Supply, Dual (V±) | ±15V |
| Height Seated (Max) | 5.08mm |
| Width | 7.62mm |
| RoHS Status | Non-RoHS Compliant |
9204201EA Overview
The electronic component is convenient to ship overseas because it is packed in a 16-CDIP (0.300, 7.62mm). To ensure high reliability, a new packaging method Bulk is used. Through Hole is where this multiplexer is located. 8:1 is the ratio of multiplexer to demultiplexer circuits. Extended operating temperature around -55°C~125°C TA. Total terminations are 16. This electronic part offers high-quality output due to its 8 channels. If the voltage supply is 15V volts, the electrical component should be turned on and run. A total of 16 pins are injected into the body of the electronic part. 1 circuits are used in this analogue multiplexer. normally, users should not supply switches with voltages higher than 44V. It is recommended that the electrical component receives a voltage of 13V. Dual supply volatge is feasible for this multiplexer. But it should not go beyond 20V. It is recommended that you attach at least 5V to your dual power supply. This product is integrated with an analog integrated circuit (IC) of type SINGLE-ENDED MULTIPLEXER.
9204201EA Features
8 Channels
9204201EA Applications
There are a lot of Vishay Siliconix 9204201EA Analog Switches & Multiplexers ICs applications.
- Access Concentrators
- USB 1.1 signal switching circuits
- Battery Powered Instruments
- Relay Replacement
- SDH/SONET multiplexers
- Avionics and Military Systems
- Modems
- Cable Telephony – NIU, Set-Top Box, Home Side Box
- Audio and video switching
- Voice over IP/DSL – Integrated Access Devices, Smart
