A2550KLPTR-T
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-TSSOP (0.173, 4.40mm Width) Exposed Pad |
| Number of Pins | 16 |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2002 |
| JESD-609 Code | e3 |
| Feature | 5V Regulated Output, Status Flag |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 2 (1 Year) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Peripheral Drivers |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 9V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | A2550 |
| Pin Count | 16 |
| Number of Outputs | 3 |
| Output Type | N-Channel |
| Supply Voltage-Max (Vsup) | 40V |
| Power Supplies | 7/40V |
| Supply Voltage-Min (Vsup) | 7V |
| Interface | On/Off |
| Current - Output (Max) | 200mA |
| Output Configuration | Low Side |
| Input Type | Non-Inverting |
| Switch Type | Relay, Solenoid Driver |
| Ratio - Input:Output | 1:1 |
| Voltage - Load | 7V~40V |
| Driver Number of Bits | 3 |
| Fault Protection | Current Limiting (Fixed), Over Temperature |
| Screening Level | AEC-Q100 |
| Turn On Time | 2 μs |
| Rds On (Typ) | 5 Ω |
| Turn Off Time | 1 μs |
| Built-in Protections | TRANSIENT; OVER CURRENT; OVER VOLTAGE; THERMAL; UNDER VOLTAGE |
| Output Current Flow Direction | SOURCE |
| Height Seated (Max) | 1.2mm |
| Length | 5mm |
| Width | 4.4mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
A2550KLPTR-T Overview
The LED driver's packaged as a Tape & Reel (TR).It is included in the package 16-TSSOP (0.173, 4.40mm Width) Exposed Pad.The lighting driver is mounted in the Surface Mount position.This switch is of type Relay, Solenoid Driver.It is recommended that the temperature be set to -40°C~125°C TA for reliable performance.There are 3 outputs available on this lighting driver.It has a maximum output voltage of N-Channel volts.It is equipped with 5V Regulated Output, Status Flag features.It is a member of the A2550 family.The termination count is 16.The operation is carried out using the 16 pins.As far as the lighting driver is concerned, there are 1 functions.The maximum output of the LED driving board is 200mAV.The supply voltage can be 9V for high efficiency.The lighting driver is mounted in the direction of Surface Mount.The LED driving board is equipped with a total of 16 pins.This LED driver is self-contained in an econtainer with a capacity of Peripheral Drivers.A maximum supply voltage of 40V is set in Vsup.In order for this lighting driver to operate normally, the supply voltage (Vsup) should remain above 7V.A 7/40V power supply is used by the part.
A2550KLPTR-T Features
Supplied from 9V
A2550KLPTR-T Applications
There are a lot of Allegro MicroSystems A2550KLPTR-T Power Switches ICs applications.
- Portable GPS Device
- Portable GPS
- PDAs
- Solid-State Drives
- Hot Swap
- USB Power Distribution
- Notebook PC
- Storage (HDDs, SSDs)
- Smart Phones, Feature Phones
- Wireless Headsets
