A6A595KA
| Parameters | |
|---|---|
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 20-DIP (0.300, 7.62mm) |
| Number of Pins | 20 |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tube |
| Published | 2006 |
| JESD-609 Code | e3 |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| ECCN Code | EAR99 |
| Resistance | 1.7Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Peripheral Drivers |
| Technology | CMOS |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | NOT SPECIFIED |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 2.54mm |
| Reach Compliance Code | unknown |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | A6A595 |
| Pin Count | 20 |
| Number of Outputs | 8 |
| Qualification Status | Not Qualified |
| Output Type | N-Channel |
| Max Output Current | 1.1A |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Power Supplies | 5V |
| Interface | Strobe, Serial |
| Output Configuration | Low Side |
| Voltage - Supply (Vcc/Vdd) | 4.5V~5.5V |
| Propagation Delay | 100 ns |
| Input Type | Non-Inverting |
| Switch Type | Latched Driver |
| Output Current per Channel | 350mA |
| Ratio - Input:Output | 1:8 |
| Voltage - Load | 50V Max |
| Driver Number of Bits | 8 |
| Fault Protection | Current Limiting (Fixed) |
| Output Peak Current Limit-Nom | 1.1A |
| Rds On (Typ) | 1 Ω |
| Built-in Protections | TRANSIENT; OVER CURRENT |
| Output Current Flow Direction | SINK |
| Height Seated (Max) | 5.33mm |
| Length | 25.905mm |
| Width | 7.62mm |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
A6A595KA Overview
The LED driver's packaged as a Tube.In the 20-DIP (0.300, 7.62mm) package, it is included.It has been mounted as Through Hole on the LED driver.There is a Latched Driver switch type associated with it.It is recommended to set the temperature to -40°C~125°C TA in order to ensure reliable operation.By default, it is set to output 8.A supply voltage of 4.5V~5.5V is required for it to operate.There is a maximum output voltage of N-Channel volts on this LED driver.The A6A595 family contains this object.It has a total of 20 terminations.For operation, we use the 20 pins.It contains 1 functions.To comply with the operation criteria, the maximum output current is reduced to 1.1A.It is possible to achieve a high level of efficiency with a supply voltage of 5V.In this case, it is mounted in the way of Through Hole.The LED driver has a total of 20 pins.The LED driver has 1.7Ohm resistance.A self-contained container with a capacity of Peripheral Drivers contains this lighting driver.This part's power supply is 5V.When using this LED driving board, it is recommended that the supply voltage is set to 5V.Total, there are 1 elements.
A6A595KA Features
Supplied from 5V
Resistance of 1.7Ohm
A6A595KA Applications
There are a lot of Allegro MicroSystems A6A595KA Power Switches ICs applications.
- Hard Disk Drives
- Wireless Modem Data Cards
- HDD, SSD
- PC Card Hot Swap
- Solid State Drivers
- Wireless/Networking Cards
- Notebook and Tablet Computers
- Portable/Handheld Devices
- Solid-State Drives
- Smart Phones, Feature Phones
