Parameters |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
8-TFSOJ (0.069, 1.75mm Width) |
Number of Pins |
8 |
Operating Temperature |
-40°C~85°C TA |
Packaging |
Tape & Reel (TR) |
Published |
2008 |
Feature |
Status Flag |
Part Status |
Obsolete |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
8 |
Resistance |
340mOhm |
Subcategory |
Peripheral Drivers |
Max Power Dissipation |
667mW |
Terminal Position |
DUAL |
Terminal Form |
J BEND |
Number of Functions |
1 |
Supply Voltage |
5V |
Terminal Pitch |
0.5mm |
Pin Count |
8 |
Number of Outputs |
1 |
Output Type |
P-Channel |
Max Output Current |
2A |
Operating Supply Voltage |
5.5V |
Power Supplies |
5V |
Interface |
On/Off |
Output Configuration |
High Side |
Output Current |
2A |
Voltage - Supply (Vcc/Vdd) |
Not Required |
Max Supply Current |
25μA |
Input Type |
Non-Inverting |
Turn On Delay Time |
200 μs |
Switch Type |
General Purpose |
Min Input Voltage |
2.4V |
Max Input Voltage |
5.5V |
Turn-Off Delay Time |
100 μs |
Ratio - Input:Output |
1:1 |
Voltage - Load |
2.4V~5.5V |
Driver Number of Bits |
1 |
Fault Protection |
Current Limiting (Adjustable), Over Temperature, Reverse Current, UVLO |
Output Peak Current Limit-Nom |
1A |
Rds On (Typ) |
160m Ω |
Built-in Protections |
TRANSIENT; OVER CURRENT; THERMAL; UNDER VOLTAGE |
Length |
2mm |
Radiation Hardening |
No |
RoHS Status |
ROHS3 Compliant |
AAT4614IJS-2-T1 Overview
It is packaged in the manner of a Tape & Reel (TR).This package is included in 8-TFSOJ (0.069, 1.75mm Width).This lighting drivere has a mounting type of Surface Mount.There is a switch type of General Purpose.To ensure reliable performance, the temperature should be set to -40°C~85°C TA.The lighting driver has a total of 1 outputs that are available for use.The LED driving board operates at Not Required volts.The maximum output voltage is P-Channel volts.Status Flag features are available on the lighting driver.A total of 8 terminations can be found in it.It is necessary to use the 8 pins in order to operate the LED driver.Currently, there are 1 functions associated with the lighting driver.It is necessary to reduce the maximum output current to 2A to meet the operation criteria.It is possible to obtain high efficiency with a supply voltage of 5V.In this case, it is mounted in the way of Surface Mount.A total of 8 pins are included in this LED driver.Lighting drivers with 340mOhm resistance are used.In this case, the output current is set to 2A.Self-contained LED driver with Peripheral Drivers capacity in an econtainer.It has a power supply of 5V.A supply voltage of 5.5V is recommended for maximum efficiency.It has a maximum input voltage of 5.5V volts.There is a minimum input voltage of 2.4V volts for this LED driver.25μA is the maximum current required to operate it.
AAT4614IJS-2-T1 Features
Supplied from 5V
Resistance of 340mOhm
AAT4614IJS-2-T1 Applications
There are a lot of Skyworks Solutions Inc. AAT4614IJS-2-T1 Power Switches ICs applications.
- PDAs
- Hot Swap
- Portable GPS
- USB Power Distribution
- Low Voltage I/O System Power
- Portable Music Players
- Mobile Communication Devices
- Wearable Devices
- Wireless/Networking Cards
- Hot Swap