AD711JNZ
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 2 weeks ago) |
| Contact Plating | Tin |
| Mounting Type | Through Hole |
| Package / Case | 8-DIP (0.300, 7.62mm) |
| Surface Mount | NO |
| Number of Pins | 8 |
| Operating Temperature | 0°C~70°C |
| Packaging | Tube |
| JESD-609 Code | e3 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Subcategory | Operational Amplifier |
| Max Power Dissipation | 500mW |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Terminal Pitch | 2.54mm |
| Base Part Number | AD711 |
| Pin Count | 8 |
| Operating Supply Voltage | 15V |
| Number of Channels | 1 |
| Operating Supply Current | 2.8mA |
| Nominal Supply Current | 2.5mA |
| Power Dissipation | 500mW |
| Quiescent Current | 2.8mA |
| Slew Rate | 20V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | J-FET |
| Common Mode Rejection Ratio | 88 dB |
| Current - Input Bias | 15pA |
| Voltage - Supply, Single/Dual (±) | 9V~36V ±4.5V~18V |
| Output Current per Channel | 25mA |
| Input Offset Voltage (Vos) | 1mV |
| Bandwidth | 3MHz |
| Gain Bandwidth Product | 4MHz |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Unity Gain BW-Nom | 4000 kHz |
| Voltage Gain | 112.04dB |
| Power Supply Rejection Ratio (PSRR) | 110dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Voltage - Input Offset | 300μV |
| Settling Time | 1 μs |
| Low-Bias | YES |
| Dual Supply Voltage | 15V |
| Input Capacitance | 5.5pF |
| Input Offset Current-Max (IIO) | 0.0006μA |
| Input Voltage Noise Density | 45nV/sqrt Hz |
| Height | 3.43mm |
| Length | 9.27mm |
| Width | 7.24mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
AD711JNZ Overview
Packaged in a 8-DIP (0.300, 7.62mm) case, the buffer op amp is ready to use. J-FET-type instrumentation amplifiers are used in this application. It comes in a Tube case, which protects instrumentation amplifier from damage during delivery. There have been a total of 8 terminations over the past year. It consists of a total of 8 pins in total. I would like you to keep in mind that this buffer amplifier needs to be run at a voltage of 15V. This particular linear amplifier is a type of Operational Amplifier device, to be precise. In total, the buffer amplifier consists of 8 pins. There is an input offset voltage of 1mV for this buffer op amp. For this electronic part, it is recommended that you mount it with type Through Hole. Regarding the operating temperature of this device, instrumentation amplifier performs well at a temperature of 0°C~70°C . It is possible to operate this buffer amplifier from a supply current of 2.8mA . There should be no change in the voltage gain at 112.04dB. There are a total of 1 channels available on the op amps. The operating supply voltage of instrumentation amplifier is rated 15V voltage. There is an 2.8mA quiescent current in linear amplifier.
AD711JNZ Features
8 Pins
supply voltage of 15V
112.04dB voltage gain
AD711JNZ Applications
There are a lot of Analog Devices Inc. AD711JNZ Instrumentational OP Amps applications.
- Mobile phone
- Inverse/same-phase proportional circuit
- Power control
- MP3
- E-book readers
- Medical instruments
- Active probe
- Industrial control system
- Measurements of Wheatstone bridge
- High-frequency data acquisition systems
