AD711KNZ
| Parameters | |
|---|---|
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Subcategory | Operational Amplifier |
| Max Power Dissipation | 500mW |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Terminal Pitch | 2.54mm |
| Base Part Number | AD711 |
| Pin Count | 8 |
| Number of Channels | 1 |
| Operating Supply Current | 2.8mA |
| Power Dissipation | 500mW |
| Quiescent Current | 2.8mA |
| Supply Current-Max | 3mA |
| Slew Rate | 20V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | J-FET |
| Common Mode Rejection Ratio | 88 dB |
| Current - Input Bias | 15pA |
| Voltage - Supply, Single/Dual (±) | 9V~36V ±4.5V~18V |
| Output Current per Channel | 25mA |
| Input Offset Voltage (Vos) | 1mV |
| Bandwidth | 4MHz |
| Gain Bandwidth Product | 4MHz |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Unity Gain BW-Nom | 4000 kHz |
| Voltage Gain | 112.04dB |
| Power Supply Rejection Ratio (PSRR) | 110dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Voltage - Input Offset | 200μV |
| Settling Time | 1 μs |
| Low-Bias | YES |
| Dual Supply Voltage | 15V |
| Input Capacitance | 5.5pF |
| Input Offset Current-Max (IIO) | 0.0006μA |
| Input Voltage Noise Density | 45nV/sqrt Hz |
| Height | 3.43mm |
| Length | 9.27mm |
| Width | 7.24mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 3 months ago) |
| Contact Plating | Tin |
| Mounting Type | Through Hole |
| Package / Case | 8-DIP (0.300, 7.62mm) |
| Surface Mount | NO |
| Number of Pins | 8 |
| Operating Temperature | 0°C~70°C |
| Packaging | Tube |
| JESD-609 Code | e3 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
AD711KNZ Overview
There is a 8-DIP (0.300, 7.62mm) case package that contains the instrumentation amplifiers. Op amps are J-FET types of amplifier on the chip. A Tube case is used for delivering the op amp. It is estimated that there will be at least 8 terminations this year. A total of 8 pins are located on this board. Please take in mind that op amp should be run at 15V. I would like to specify that this buffer amplifier belongs to the Operational Amplifier-type of devices. 8 pins are located on the operational amplifiers. In terms of input offset voltage, operational amplifier rates 1mV. For this electrical component, Through Hole is the recommended mounting type. With regard to operating temperature, this op amp functions well at 0°C~70°C. In order for this instrumentation amplifier to operate, the supply current needs to be between 2.8mA and 10 . There should be no change in the voltage gain at 112.04dB. Instrumentation amplifier has 1 channels on it. 2.8mA quiescent currents are flowing through buffer op amp.
AD711KNZ Features
8 Pins
supply voltage of 15V
112.04dB voltage gain
AD711KNZ Applications
There are a lot of Analog Devices Inc. AD711KNZ Instrumentational OP Amps applications.
- Power generator
- Medical imaging
- Laptop
- Video amplifiers
- Comparator
- Signal transformation
- Tablets
- Cinema or auditorium audio system
- Instrumentation
- Multiplication circuits
