AD712JR
| Parameters | |
|---|---|
| Contact Plating | Lead, Tin |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | 0°C~70°C |
| Packaging | Tube |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Subcategory | Operational Amplifier |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 2 |
| Supply Voltage | 15V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | AD712 |
| Pin Count | 8 |
| Operating Supply Voltage | 5V |
| Number of Channels | 2 |
| Operating Supply Current | 5mA |
| Quiescent Current | 2.8mA |
| Slew Rate | 20V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | J-FET |
| Common Mode Rejection Ratio | 88 dB |
| Current - Input Bias | 25pA |
| Voltage - Supply, Single/Dual (±) | ±4.5V~18V |
| Output Current per Channel | 25mA |
| Input Offset Voltage (Vos) | 300μV |
| Bandwidth | 4MHz |
| Gain Bandwidth Product | 4MHz |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Unity Gain BW-Nom | 4000 kHz |
| Voltage Gain | 112.04dB |
| Power Supply Rejection Ratio (PSRR) | 95dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Low-Bias | YES |
| Bias Current-Max (IIB) @25C | 0.0001μA |
| Dual Supply Voltage | 15V |
| Input Capacitance | 5.5pF |
| Input Offset Current-Max (IIO) | 0.0006μA |
| Input Voltage Noise Density | 45nV/sqrt Hz |
| Height | 1.5mm |
| Length | 5mm |
| Width | 4mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
AD712JR Overview
There is a 8-SOIC (0.154, 3.90mm Width) case package that contains the instrumentation amplifiers. The instrumentation amplifier in this picture is of the J-FET-type. As far as the packaging is concerned, buffer op amp is delivered in a Tube case. The number of terminations is approaching the 8 mark. The total number of pins on linear amplifier is 8. It is important to remember that this op amp should be operated at a voltage of 15V volts. This particular linear amplifier is a type of Operational Amplifier device, to be precise. It has 8 pins that make up the linear amplifier. With regards to the offset voltage of the input, buffer amplifier is rated at 300μV. This electronic component is recommended to be mounted using the mounting type Surface Mount. With regard to operating temperature, op amp ranges 0°C~70°C. You can run this op amp ic on 5mA . Voltage gain should remain at 112.04dB. Op amp ic has 2 channels. The operating supply voltage of the buffer op amp is rated at 5V. Buffer amplifier has a quiescent current of 2.8mA.
AD712JR Features
8 Pins
supply voltage of 15V
112.04dB voltage gain
AD712JR Applications
There are a lot of Analog Devices Inc. AD712JR Instrumentational OP Amps applications.
- Tablets
- High-frequency data acquisition systems
- Multimedia playback equipment
- Band-stop filter
- Car stereo
- Video data acquisition
- Navigation
- Medical imaging
- Portable electronic products powered by batteries
- Proportional operation circuits
