AD712KRZ-REEL
| Parameters | |
|---|---|
| Amplifier Type | J-FET |
| Common Mode Rejection Ratio | 88 dB |
| Current - Input Bias | 20pA |
| Voltage - Supply, Single/Dual (±) | ±4.5V~18V |
| Output Current per Channel | 25mA |
| Input Offset Voltage (Vos) | 1mV |
| Gain Bandwidth Product | 4MHz |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Unity Gain BW-Nom | 4000 kHz |
| Voltage Gain | 112.04dB |
| Power Supply Rejection Ratio (PSRR) | 95dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Voltage - Input Offset | 200μV |
| Settling Time | 1 μs |
| Low-Bias | YES |
| Bias Current-Max (IIB) @25C | 0.000075μA |
| Dual Supply Voltage | 15V |
| Input Capacitance | 5.5pF |
| Input Offset Current-Max (IIO) | 0.0006μA |
| Input Voltage Noise Density | 45nV/sqrt Hz |
| Height Seated (Max) | 1.75mm |
| Length | 4.9mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 1 month ago) |
| Contact Plating | Tin |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | 0°C~70°C |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e3 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 15V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | AD712 |
| Pin Count | 8 |
| Qualification Status | Not Qualified |
| Number of Channels | 2 |
| Operating Supply Current | 5.6mA |
| Quiescent Current | 2.8mA |
| Slew Rate | 20V/μs |
| Architecture | VOLTAGE-FEEDBACK |
AD712KRZ-REEL Overview
A 8-SOIC (0.154, 3.90mm Width) case is used to package the op amp. J-FET-type instrumentation amplifiers are used in this application. Instrumentation amplifier is delivered in a Tape & Reel (TR) case. There is a growing number of terminations approaching the number of 8. A total of 8 pins are attached to buffer op amp. I would like you to keep in mind that this buffer amplifier needs to be run at a voltage of 15V. I would like to specify that this buffer amplifier belongs to the Operational Amplifier-type of devices. Linear amplifier includes 8 pins. Regarding input offset voltage, op amp rates 1mV. For this electrical component, the recommended mounting type is Surface Mount, which is the most common. The buffer amplifier functions well at 0°C~70°C as far as operating temperature is concerned. This op amp can operate from a supply current at 5.6mA. Voltage gain should remain at 112.04dB. On the buffer amps, there are 2 channels that can be used. For packing the buffer amplifier, the TAPE AND REEL-axis is adopted. Buffer amplifier has a quiescent current of 2.8mA.
AD712KRZ-REEL Features
8 Pins
supply voltage of 15V
112.04dB voltage gain
AD712KRZ-REEL Applications
There are a lot of Analog Devices Inc. AD712KRZ-REEL Instrumentational OP Amps applications.
- Power control
- Large motor controllers
- Portable media players
- Signal amplification
- Comparator
- Subtraction operation circuits
- Portable electronic products powered by batteries
- Video conversion and routing
- Vehicle electronics
- earphone
