AD713AQ
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 1 month ago) |
| Contact Plating | Lead, Tin |
| Mounting Type | Through Hole |
| Package / Case | 14-CDIP (0.300, 7.62mm) |
| Surface Mount | NO |
| Number of Pins | 14 |
| Operating Temperature | -40°C~85°C |
| Packaging | Tube |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Terminal Finish | Tin/Lead (Sn63Pb37) |
| Subcategory | Operational Amplifier |
| Technology | BIFET |
| Terminal Position | DUAL |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Base Part Number | AD713 |
| Pin Count | 14 |
| Number of Elements | 4 |
| Operating Supply Current | 12mA |
| Quiescent Current | 3mA |
| Supply Current-Max | 13.5mA |
| Slew Rate | 20V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | J-FET |
| Common Mode Rejection Ratio | 88 dB |
| Current - Input Bias | 55pA |
| Voltage - Supply, Single/Dual (±) | 9V~36V ±4.5V~18V |
| Output Current per Channel | 25mA |
| Input Offset Voltage (Vos) | 1.5mV |
| Bandwidth | 4MHz |
| Gain Bandwidth Product | 4MHz |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Unity Gain BW-Nom | 4000 kHz |
| Voltage Gain | 112.04dB |
| Average Bias Current-Max (IIB) | 0.0002μA |
| Power Supply Rejection Ratio (PSRR) | 95dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 18V |
| Voltage - Input Offset | 300μV |
| Settling Time | 1 μs |
| Low-Bias | YES |
| Bias Current-Max (IIB) @25C | 0.0002μA |
| Dual Supply Voltage | 15V |
| Input Capacitance | 5.5pF |
| Neg Supply Voltage-Max (Vsup) | -18V |
| Input Voltage Noise Density | 45nV/sqrt Hz |
| Height | 3.56mm |
| Length | 19.94mm |
| Width | 7.87mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
AD713AQ Overview
Packaged in a 14-CDIP (0.300, 7.62mm) case, the buffer op amp is ready to use. The instrumentation amplifier in this picture is of the J-FET-type. In the case of Tube cases, linear amplifier will be delivered. There have been a total of 14 terminations over the past year. Buffer amplifier has a total of 14 pins on it. The linear amplifier should be run at 15V at all times, so please keep that in mind when using it. I would like to specify that this buffer amplifier belongs to the Operational Amplifier-type of devices. An 14-pin op amp ic is included in the package. In terms of input offset voltage, operational amplifier rates 1.5mV. It is recommended that this electronic component be mounted using the Through Hole mounting type. With regard to operating temperature, this op amp functions well at -40°C~85°C. A supply current of 12mA can be used to operate this linear amplifier. The voltage gain should stay at 112.04dB. The op amp is rated for an operating supply voltage of 4. 3mA quiescent currents are flowing through buffer op amp.
AD713AQ Features
14 Pins
supply voltage of 15V
112.04dB voltage gain
AD713AQ Applications
There are a lot of Analog Devices Inc. AD713AQ Instrumentational OP Amps applications.
- Radiation thermometry transducers
- Tablets
- High speed sample
- Oscilloscopes
- Radar
- Power control
- Television
- Portable media players
- Large motor controllers
- Hand-held batteries
