AD743JR-16-REEL7
| Parameters | |
|---|---|
| Contact Plating | Lead, Tin |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.295, 7.50mm Width) |
| Surface Mount | YES |
| Number of Pins | 16 |
| Operating Temperature | 0°C~70°C |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Reach Compliance Code | not_compliant |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | AD743 |
| Pin Count | 16 |
| Qualification Status | Not Qualified |
| Number of Channels | 1 |
| Operating Supply Current | 10mA |
| Quiescent Current | 10mA |
| Slew Rate | 2.8V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | J-FET |
| Common Mode Rejection Ratio | 95 dB |
| Current - Input Bias | 250pA |
| Voltage - Supply, Single/Dual (±) | 9.6V~36V ±4.8V~18V |
| Output Current per Channel | 40mA |
| Input Offset Voltage (Vos) | 1mV |
| Gain Bandwidth Product | 4.5MHz |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Unity Gain BW-Nom | 4500 kHz |
| Voltage Gain | 132.04dB |
| Average Bias Current-Max (IIB) | 0.0006μA |
| Power Supply Rejection Ratio (PSRR) | 96dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Voltage - Input Offset | 250μV |
| Settling Time | 6 μs |
| Low-Bias | YES |
| Bias Current-Max (IIB) @25C | 0.0004μA |
| Dual Supply Voltage | 15V |
| Input Capacitance | 18pF |
| Input Offset Current-Max (IIO) | 0.0064μA |
| Input Voltage Noise Density | 5.5nV/sqrt Hz |
| Height Seated (Max) | 2.65mm |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
AD743JR-16-REEL7 Overview
Packaging for the buffer amplifier is in the form of a 16-SOIC (0.295, 7.50mm Width) case. A J-FET-type buffer amplifier is shown here. A Tape & Reel (TR) case is used for delivering the op amp. There is a growing number of terminations approaching the number of 16. It consists of a total of 16 pins in total. The linear amplifier should be run at 15V at all times, so please keep that in mind when using it. It should be noted that this type of buffer amplifier is exactly what is known as a Operational Amplifier device. 16 pins are available on the instrumentation amplifier. The input offset voltage is 1mV. This electronic component is recommended to be mounted using the mounting type Surface Mount. According to the manufacturer, this buffer op amp works well at 0°C~70°C , which is a good operating temperature. A supply current of 10mA can be used to operate this linear amplifier. 132.04dB should remain the voltage gain. Op amp ic has 1 channels. To pack the operational amplifier ics, TAPE AND REEL is adopted as the packing method. There is an 10mA quiescent current in linear amplifier.
AD743JR-16-REEL7 Features
16 Pins
supply voltage of 15V
132.04dB voltage gain
AD743JR-16-REEL7 Applications
There are a lot of Analog Devices Inc. AD743JR-16-REEL7 Instrumentational OP Amps applications.
- Thermocouples
- Weighing systems
- Weak signal detection
- Test equipment
- Instrumentation
- Multiplication circuits
- Subtraction operation circuits
- Portable media players
- Video amplifiers
- Information processing
