AD743JRZ-16-REEL7
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 1 month ago) |
| Contact Plating | Tin |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.295, 7.50mm Width) |
| Surface Mount | YES |
| Number of Pins | 16 |
| Operating Temperature | 0°C~70°C |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e3 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | AD743 |
| Pin Count | 16 |
| Qualification Status | Not Qualified |
| Number of Channels | 1 |
| Operating Supply Current | 10mA |
| Quiescent Current | 10mA |
| Slew Rate | 2.8V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | J-FET |
| Common Mode Rejection Ratio | 95 dB |
| Current - Input Bias | 250pA |
| Voltage - Supply, Single/Dual (±) | 9.6V~36V ±4.8V~18V |
| Output Current per Channel | 40mA |
| Input Offset Voltage (Vos) | 1mV |
| Gain Bandwidth Product | 4.5MHz |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Unity Gain BW-Nom | 4500 kHz |
| Voltage Gain | 132.04dB |
| Average Bias Current-Max (IIB) | 0.0006μA |
| Power Supply Rejection Ratio (PSRR) | 96dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Voltage - Input Offset | 250μV |
| Settling Time | 6 μs |
| Low-Bias | YES |
| Bias Current-Max (IIB) @25C | 0.0004μA |
| Dual Supply Voltage | 15V |
| Input Capacitance | 18pF |
| Input Offset Current-Max (IIO) | 0.0064μA |
| Input Voltage Noise Density | 5.5nV/sqrt Hz |
| Height Seated (Max) | 2.65mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
AD743JRZ-16-REEL7 Overview
A 16-SOIC (0.295, 7.50mm Width) case is used to package the op amp. A J-FET-type buffer amplifier is shown here. There is a Tape & Reel (TR) case that is delivered with the instrumentation amplifiers. The number of terminations approaches 16. Buffer amplifier has a total of 16 pins on it. It would be helpful if you could remember that this op amp ic should be powered by an 15V battery. It should be noted that this op amp is a type of Operational Amplifier device. 16 pins are available on the instrumentation amplifier. As far as the input offset voltage is concerned, linear amplifier rates at 1mV. This electronic part is best mounted with type Surface Mount. Regarding the operating temperature of this device, instrumentation amplifier performs well at a temperature of 0°C~70°C . Operational amplifier can operate supply current at 10mA. Voltage gain should remain at 132.04dB. Buffer op amp is equipped with 1 channels on the device. For the packing of the instrumentation amplifier, TAPE AND REEL is adopted. The quiescent current is 10mA.
AD743JRZ-16-REEL7 Features
16 Pins
supply voltage of 15V
132.04dB voltage gain
AD743JRZ-16-REEL7 Applications
There are a lot of Analog Devices Inc. AD743JRZ-16-REEL7 Instrumentational OP Amps applications.
- Measurements of Wheatstone bridge
- Digital cameras
- Weak signal detection
- Computer workstations
- Video amplifiers
- Radiation thermometry transducers
- Polarized electrodes
- Multiplication circuits
- High/low-pass filter circuit
- Medical imaging
