AD746JNZ
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 1 month ago) |
| Contact Plating | Tin |
| Mounting Type | Through Hole |
| Package / Case | 8-DIP (0.300, 7.62mm) |
| Surface Mount | NO |
| Number of Pins | 8 |
| Operating Temperature | 0°C~70°C |
| Packaging | Tube |
| JESD-609 Code | e3 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Subcategory | Operational Amplifier |
| Max Power Dissipation | 500mW |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Number of Functions | 2 |
| Supply Voltage | 15V |
| Base Part Number | AD746 |
| Pin Count | 8 |
| Number of Channels | 2 |
| Operating Supply Current | 8mA |
| Power Dissipation | 500mW |
| Quiescent Current | 7mA |
| Supply Current-Max | 10mA |
| Slew Rate | 75V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | J-FET |
| Common Mode Rejection Ratio | 88 dB |
| Current - Input Bias | 110pA |
| Voltage - Supply, Single/Dual (±) | 9V~36V ±4.5V~18V |
| Output Current per Channel | 25mA |
| Input Offset Voltage (Vos) | 1.5mV |
| Bandwidth | 13MHz |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Unity Gain BW-Nom | 13000 kHz |
| Voltage Gain | 109.54dB |
| Average Bias Current-Max (IIB) | 0.00035μA |
| Power Supply Rejection Ratio (PSRR) | 95dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Voltage - Input Offset | 300μV |
| Settling Time | 500 ns |
| Low-Bias | YES |
| Max Frequency | 10kHz |
| Bias Current-Max (IIB) @25C | 0.00035μA |
| Dual Supply Voltage | 15V |
| Input Capacitance | 5.5pF |
| Input Voltage Noise Density | 45nV/sqrt Hz |
| Height | 3.43mm |
| Length | 9.27mm |
| Width | 7.24mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
AD746JNZ Overview
Op amp is packaged in 8-DIP (0.300, 7.62mm) case. The instrumentation amplifier in this picture is of the J-FET-type. Linear amplifier is delivered in a Tube case. During the past two weeks, there have been close to 8 terminations. A total of 8 pins are attached to buffer op amp. As a reminder, this buffer op amp should be powered by 15V battery and that the battery should be inserted in the amplifier. This particular linear amplifier is a type of Operational Amplifier device, to be precise. 8 pins are located on the operational amplifiers. Regarding input offset voltage, op amp rates 1.5mV. For this electrical component, Through Hole is the recommended mounting type. With regard to operating temperature, this op amp functions well at 0°C~70°C. In order for this instrumentation amplifier to operate, the supply current needs to be between 8mA and 10 . There should be no change in the voltage gain at 109.54dB. 2 channels are available on the instrumentation amplifier. Currently, linear amplifier is operating with a quiescent current of 7mA.
AD746JNZ Features
8 Pins
supply voltage of 15V
109.54dB voltage gain
AD746JNZ Applications
There are a lot of Analog Devices Inc. AD746JNZ Instrumentational OP Amps applications.
- Test equipment
- Power generator
- earphone
- Inverse/same-phase proportional circuit
- Portable docking station
- Broadcasting
- Active probe
- High-frequency data acquisition systems
- Blood pressure sensors
- Displayers for aircraft and air transportation control systems
