AD746JRZ
| Parameters | |
|---|---|
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Subcategory | Operational Amplifier |
| Max Power Dissipation | 500mW |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 15V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | AD746 |
| Pin Count | 8 |
| Number of Channels | 2 |
| Operating Supply Current | 8mA |
| Power Dissipation | 500mW |
| Quiescent Current | 7mA |
| Supply Current-Max | 10mA |
| Slew Rate | 75V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | J-FET |
| Common Mode Rejection Ratio | 88 dB |
| Current - Input Bias | 110pA |
| Voltage - Supply, Single/Dual (±) | 9V~36V ±4.5V~18V |
| Output Current per Channel | 25mA |
| Input Offset Voltage (Vos) | 1.5mV |
| Bandwidth | 13MHz |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Unity Gain BW-Nom | 13000 kHz |
| Voltage Gain | 109.54dB |
| Average Bias Current-Max (IIB) | 0.00035μA |
| Power Supply Rejection Ratio (PSRR) | 95dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Voltage - Input Offset | 300μV |
| Settling Time | 500 ns |
| Low-Bias | YES |
| Bias Current-Max (IIB) @25C | 0.00035μA |
| Dual Supply Voltage | 15V |
| Input Capacitance | 5.5pF |
| Input Voltage Noise Density | 45nV/sqrt Hz |
| Height | 1.5mm |
| Length | 5mm |
| Width | 4mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 1 month ago) |
| Contact Plating | Tin |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | 0°C~70°C |
| Packaging | Tube |
| JESD-609 Code | e3 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
AD746JRZ Overview
It is packaged in an 8-SOIC (0.154, 3.90mm Width)-case that protects the operational amplifiers from damage. An op amp ic of the J-FET type. Instrumentation amplifier is delivered in a Tube case. During the past two weeks, there have been close to 8 terminations. A total of 8 pins are located on this board. This linear amplifier should be powered by an 15V battery. This particular linear amplifier is a type of Operational Amplifier device, to be precise. 8 pins are located on the operational amplifiers. The input offset voltage is 1.5mV. For this electrical component, the recommended mounting type is Surface Mount, which is the most common. The buffer amplifier functions well at 0°C~70°C as far as operating temperature is concerned. You can run this op amp ic on 8mA . 109.54dB should remain the voltage gain. 2 channels are available on the instrumentation amplifier. There is an 7mA quiescent current running through op amp ic.
AD746JRZ Features
8 Pins
supply voltage of 15V
109.54dB voltage gain
AD746JRZ Applications
There are a lot of Analog Devices Inc. AD746JRZ Instrumentational OP Amps applications.
- Proportional counter tubes
- Power transmission
- Blood pressure sensors
- Signal amplification
- Displayers for aircraft and air transportation control systems
- Precision measurement
- Industrial applications including automation
- Logarithmic operation circuits
- Signal filtering
- Biopotential
