AD746SQ/883B
| Parameters | |
|---|---|
| Time@Peak Reflow Temperature-Max (s) | NOT APPLICABLE |
| Base Part Number | AD746 |
| Pin Count | 8 |
| Number of Elements | 2 |
| Temperature Grade | MILITARY |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 9.6V |
| Operating Supply Current | 8mA |
| Power Dissipation | 500mW |
| Quiescent Current | 7mA |
| Supply Current-Max | 10mA |
| Slew Rate | 75 V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | OPERATIONAL AMPLIFIER |
| Common Mode Rejection Ratio | 88 dB |
| Input Offset Voltage (Vos) | 1.5mV |
| Gain Bandwidth Product | 10MHz |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Unity Gain BW-Nom | 13000 kHz |
| Voltage Gain | 109.54dB |
| Average Bias Current-Max (IIB) | 0.00035μA |
| Power Supply Rejection Ratio (PSRR) | 95dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Settling Time | 500 ns |
| Max Dual Supply Voltage | 18V |
| Low-Bias | YES |
| Min Dual Supply Voltage | 4.5V |
| Bias Current-Max (IIB) @25C | 0.00035μA |
| Dual Supply Voltage | 15V |
| Input Capacitance | 5.5pF |
| Input Bias Current | 110pA |
| Input Voltage Noise Density | 45nV/sqrt Hz |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 3 weeks ago) |
| Contact Plating | Lead, Tin |
| Package / Case | Q |
| Surface Mount | NO |
| Number of Pins | 8 |
| Packaging | Tube |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Tin/Lead (Sn63Pb37) |
| Max Operating Temperature | 125°C |
| Min Operating Temperature | -55°C |
| Subcategory | Operational Amplifier |
| Max Power Dissipation | 500mW |
| Technology | BIFET |
| Terminal Position | DUAL |
| Terminal Form | THROUGH-HOLE |
| Peak Reflow Temperature (Cel) | NOT APPLICABLE |
| Number of Functions | 2 |
| Supply Voltage | 15V |
| Reach Compliance Code | not_compliant |
AD746SQ/883B Overview
It is packaged in an Q-case that protects the operational amplifiers from damage. Op amps are OPERATIONAL AMPLIFIER types of amplifier on the chip. A Tube case is used to deliver the buffer op amp. It is estimated that there will be at least 8 terminations this year. In total, there are 8 pins on this op amp ic. It is important to remember that this op amp should be operated at a voltage of 15V volts. This particular linear amplifier is a type of Operational Amplifier device, to be precise. 8 pins are located on the operational amplifiers. Op amp rates 1.5mV as input offset voltage. This op amp can operate from a supply current at 8mA. Op amp is a member of the 109.54dB's 109.54dB family. To operate this buffer amplifier, the temperature must not be lower than -55°C. You should not use op amp above 125°C degrees. There is a rating of 2 for the operating supply voltage of the buffer op amp. With regard tp supply voltage, op amp is used under 36V. Keeping the linear amplifier's supply voltage above 9.6V is recommended. The dual supply voltage of 18V should be used for the conduct of this electronic component. As a result, linear amplifier's quiescent current is 7mA.
AD746SQ/883B Features
8 Pins
supply voltage of 15V
109.54dB voltage gain
AD746SQ/883B Applications
There are a lot of Analog Devices Inc. AD746SQ/883B Instrumentational OP Amps applications.
- Industrial applications including automation
- Professional videography
- Automation control systems
- Micro signal measurement
- Instrumentation
- High input resistance broadband
- ECG equipment
- Polarized electrodes
- High/low-pass filter circuit
- Test and measurement instruments
