AD7511DIJN
| Parameters | |
|---|---|
| Contact Plating | Lead, Tin |
| Mounting Type | Through Hole |
| Package / Case | 16-DIP (0.300, 7.62mm) |
| Surface Mount | NO |
| Number of Pins | 16 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 100Ohm |
| Terminal Finish | Tin/Lead (Sn85Pb15) |
| Additional Feature | OVERVOLTAGE PROTECTION |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 450mW |
| Technology | CMOS |
| Peak Reflow Temperature (Cel) | NOT APPLICABLE |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Reach Compliance Code | not_compliant |
| Time@Peak Reflow Temperature-Max (s) | NOT APPLICABLE |
| Base Part Number | AD7511 |
| Pin Count | 16 |
| Qualification Status | Not Qualified |
| Operating Supply Voltage | 15V |
| Polarity | Inverting, Non-Inverting |
| Number of Channels | 4 |
| Interface | Parallel |
| Power Dissipation | 24mW |
| Max Supply Current | 800μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 350 ns |
| Supply Type | Dual |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 180 ns |
| Max Dual Supply Voltage | 17V |
| On-State Resistance (Max) | 100Ohm |
| High Level Output Current | 50mA |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Channel Capacitance (CS(off), CD(off)) | 8pF 1pF |
| On-state Resistance Match-Nom | 1Ohm |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 180ns, 350ns (Typ) |
| Channel-to-Channel Matching (ΔRon) | 1 Ω |
| Switching | BREAK-BEFORE-MAKE |
| Normal Position | NC |
| Voltage - Supply, Dual (V±) | ±15V |
| Height | 3.3mm |
| Length | 20.07mm |
| Width | 6.35mm |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
AD7511DIJN Overview
The electronic part can be shipped overseas conveniently because it is packaged in 16-DIP (0.300, 7.62mm). The advanced packaging method Tube provides high reliability. It is mounted in the position Through Hole. In the multiplexer and demultiplexer, 1:1 represents the number of circuits. Operating temperature extended to 0°C~70°C TA. Total terminations are 16. Due to its 4 channels, the electrical component produces high-quality output. In the case of a voltage supply of 15V volts, the electrical part can be powered up and run. It is injected into the electrical part body with 16 pins. A SPST - NC switching circuit is used to build these analog multiplexers. Try searching for the analog switch ic with AD7511 if you are looking for variants. It has an internal resistance of 100Ohm. For functions related to 16 pins, please refer to the datasheets. Multiplexer or Switches is a typical switch device. Analogue multiplexers of the Dual supply type that are cost-effective. When the digital multiplexer is charged above 800μA, damage can occur. Despite this switch's dual supply capability, its voltage should not exceed 17V. It can operate from 15V operating voltages. Additional features of the electronic component include: OVERVOLTAGE PROTECTION.
AD7511DIJN Features
4 Channels
Switch Circuit: SPST - NC
Additional Features: OVERVOLTAGE PROTECTION
AD7511DIJN Applications
There are a lot of Analog Devices Inc. AD7511DIJN Analog Switches & Multiplexers ICs applications.
- Battery Powered Instruments
- Residential Gateways, Home Gateway/Router
- Avionics and Military Systems
- T1/E1 Terminals
- Power routing
- DVD-R
- Battery Powered Systems
- PCMCIA cards
- Data switching
- Cell phones
