AD7511DIKNZ
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 2 weeks ago) |
| Mounting Type | Through Hole |
| Package / Case | 16-DIP (0.300, 7.62mm) |
| Surface Mount | NO |
| Number of Pins | 16 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| JESD-609 Code | e3 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 100Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Additional Feature | OVERVOLTAGE PROTECTION |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 450mW |
| Technology | CMOS |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Base Part Number | AD7511 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Operating Supply Voltage | 15V |
| Number of Channels | 4 |
| Interface | Parallel |
| Power Dissipation | 24mW |
| Max Supply Current | 800μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 350 ns |
| Supply Type | Dual |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 180 ns |
| Max Dual Supply Voltage | 17V |
| On-State Resistance (Max) | 100Ohm |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Current - Leakage (IS(off)) (Max) | 5nA |
| Channel Capacitance (CS(off), CD(off)) | 8pF 1pF |
| On-state Resistance Match-Nom | 0.75Ohm |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 180ns, 350ns (Typ) |
| Channel-to-Channel Matching (ΔRon) | 1 Ω |
| Switching | BREAK-BEFORE-MAKE |
| Drain to Source Resistance | 100Ohm |
| Normal Position | NC |
| Voltage - Supply, Dual (V±) | ±15V |
| Height | 3.3mm |
| Length | 20.07mm |
| Width | 6.35mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
AD7511DIKNZ Overview
This electronic part is conveniently packaged in 16-DIP (0.300, 7.62mm), making it easy to ship abroad. A high level of reliability can be achieved through the use of an advanced packaging method Tube. In Through Hole, you'll find this switch device. 1:1 is the ratio of multiplexer to demultiplexer circuits. Operating temperature around 0°C~70°C TA extended. A total of 16 terminations have been recorded. High-quality output is provided by the electronic component's 4 channels. An 15V voltage supply should allow the electrical part to be turned on and run. The electrical component body receives 16 pins. These analog multiplexers are built based on SPST - NC switching circuits. Try searching for the analog switch ic with AD7511 if you are looking for variants. As far as internal resistance is concerned, it has 100Ohm. Datasheets for 16 pin functions are available upon request. The analogue multiplexer in this example is a typical Multiplexer or Switches. The digital multiplexer has a low cost Dual supply. If put voltage greater than 800μA on the device, damage may be caused to the analogue multiplexer. If put voltage greater than 17V on the multiplexer, damage may be caused to the device. There are SEPARATE OUTPUT outputs on this analog switch ic. Operating voltages range from 15V. Don't miss this electronic component's additional features, such as: OVERVOLTAGE PROTECTION. Resistivity from Drain to Source is 100Ohm for this electronic part.
AD7511DIKNZ Features
4 Channels
Switch Circuit: SPST - NC
Additional Features: OVERVOLTAGE PROTECTION
Drain-to-Source resistance: 100Ohm
AD7511DIKNZ Applications
There are a lot of Analog Devices Inc. AD7511DIKNZ Analog Switches & Multiplexers ICs applications.
- Sample-and-hold systems
- High reliability control systems
- PDH Multiplexers
- Medical
- USB 1.1 signal switching circuits
- Channel Banks
- PDAs
- Mechanical reed relay replacement
- Public switching systems
- Battery-powered systems
