AD797ANZ
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 3 weeks ago) |
| Contact Plating | Tin |
| Mounting Type | Through Hole |
| Package / Case | 8-DIP (0.300, 7.62mm) |
| Surface Mount | NO |
| Number of Pins | 8 |
| Weight | 930.006106mg |
| Operating Temperature | -40°C~85°C |
| Packaging | Tube |
| JESD-609 Code | e3 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Subcategory | Operational Amplifier |
| Technology | BIPOLAR |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Terminal Pitch | 2.54mm |
| Base Part Number | AD797 |
| Pin Count | 8 |
| Number of Channels | 1 |
| Operating Supply Current | 10.5mA |
| Nominal Supply Current | 8mA |
| Quiescent Current | 10.5mA |
| Slew Rate | 20V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 130 dB |
| Current - Input Bias | 250nA |
| Max Input Voltage | 18V |
| Voltage - Supply, Single/Dual (±) | ±5V~15V |
| Output Current per Channel | 50mA |
| Supply Type | Dual |
| Input Offset Voltage (Vos) | 40μV |
| Bandwidth | 110MHz |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Unity Gain BW-Nom | 110000 kHz |
| Voltage Gain | 146.02dB |
| Average Bias Current-Max (IIB) | 3μA |
| Power Supply Rejection Ratio (PSRR) | 130dB |
| Low-Offset | YES |
| Voltage - Input Offset | 25μV |
| Settling Time | 800 ns |
| -3db Bandwidth | 8MHz |
| Dual Supply Voltage | 9V |
| Input Capacitance | 5pF |
| Height | 3.43mm |
| Length | 9.27mm |
| Width | 7.24mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
AD797ANZ Overview
There is a 8-DIP (0.300, 7.62mm) case package that contains the instrumentation amplifiers. General Purpose-type instrumentation amplifiers are used in this application. The case in which buffer amplifier is delivered is called a Tube case. The number of terminations approaches 8. The total number of pins on linear amplifier is 8. Please take in mind that this instrumentation amplifier should be run at 15V. To be specific, this instrumentation amplifier is a type of Operational Amplifier. In total, the buffer amplifier consists of 8 pins. In terms of input offset voltage, operational amplifier rates 40μV. For this electrical component, the recommended mounting type is Through Hole, which is the most common. In terms of operating temperature, this instrumentation amplifier performs well at a temperature of about -40°C~85°C . It is possible to operate this buffer amplifier from a supply current of 10.5mA . 146.02dB should be the voltage gain. Buffer op amp is equipped with 1 channels on the device. Buffer amplifier has a quiescent current of 10.5mA.
AD797ANZ Features
8 Pins
supply voltage of 15V
146.02dB voltage gain
AD797ANZ Applications
There are a lot of Analog Devices Inc. AD797ANZ Instrumentational OP Amps applications.
- Hand-held batteries
- pH (acidity)
- Large motor controllers
- Inverse/same-phase proportional circuit
- High-frequency data acquisition systems
- Digital cameras
- Radar
- Navigation
- Polarized electrodes
- Signal amplification
