AD8001AQ
| Parameters | |
|---|---|
| Terminal Pitch | 2.54mm |
| Reach Compliance Code | not_compliant |
| Time@Peak Reflow Temperature-Max (s) | NOT APPLICABLE |
| Base Part Number | AD8001 |
| Pin Count | 8 |
| Qualification Status | Not Qualified |
| Operating Supply Voltage | 9V |
| Power Supplies | +-3/+-6V |
| Number of Channels | 1 |
| Operating Supply Current | 5mA |
| Power Dissipation | 1.1W |
| Quiescent Current | 5mA |
| Slew Rate | 1200V/μs |
| Amplifier Type | Current Feedback |
| Common Mode Rejection Ratio | 54 dB |
| Current - Input Bias | 5μA |
| Voltage - Supply, Single/Dual (±) | ±3V~6V |
| Output Current per Channel | 70mA |
| Supply Type | Dual, Single |
| Input Offset Voltage (Vos) | 5.5mV |
| Gain Bandwidth Product | 795MHz |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Power Supply Rejection Ratio (PSRR) | 75dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 6.3V |
| Voltage - Input Offset | 2mV |
| Settling Time | 10 ns |
| Low-Bias | NO |
| Micropower | NO |
| -3db Bandwidth | 880MHz |
| Bias Current-Max (IIB) @25C | 25μA |
| Programmable Power | NO |
| Dual Supply Voltage | 5V |
| Input Capacitance | 1.5pF |
| Wideband | YES |
| Height | 3.56mm |
| Length | 10.29mm |
| Width | 7.87mm |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 1 month ago) |
| Contact Plating | Lead, Tin |
| Mounting Type | Through Hole |
| Package / Case | 8-CDIP (0.300, 7.62mm) |
| Surface Mount | NO |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C |
| Packaging | Tube |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | TIN LEAD |
| Subcategory | Operational Amplifier |
| Max Power Dissipation | 1.1W |
| Technology | BIPOLAR |
| Peak Reflow Temperature (Cel) | NOT APPLICABLE |
| Number of Functions | 1 |
| Supply Voltage | 5V |
AD8001AQ Overview
Packaging for the buffer amplifier is in the form of a 8-CDIP (0.300, 7.62mm) case. Current Feedback-type instrumentation amplifiers are used in this application. Instrumentation amplifier is delivered in a Tube case. A total of 8 terminations have been reported in the past few weeks. A total of 8 pins are attached to buffer op amp. It would be helpful if you could remember that this op amp ic should be powered by an 5V battery. There are two types of Operational Amplifier op amps in this case, and this device falls into one of them. There are 8 pins on this chip. With regard to input offset voltage, instrumentation amplifier is rated at 5.5mV. This electronic part is recommended for mounting type Through Hole. In terms of operating temperatures, this buffer amplifier works very well at a temperature of around -40°C~85°C . An 5mA volt supply current is needed for this linear amplifier to operate. Op amp ic has 1 channels. The operating supply voltage of instrumentation amplifier is rated 9V voltage. As a result, linear amplifier's quiescent current is 5mA.
AD8001AQ Features
8 Pins
supply voltage of 5V
AD8001AQ Applications
There are a lot of Analog Devices Inc. AD8001AQ Instrumentational OP Amps applications.
- Precision measurement
- Fission chambers
- Information processing
- Navigation
- Automotive sensors
- Band-stop filter
- Ultrasound transducers
- Communication
- Voltage regulation circuit
- Laptop
