AD8040ARUZ
| Parameters | |
|---|---|
| Operating Temperature | -40°C~125°C |
| Packaging | Tube |
| JESD-609 Code | e3 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Operational Amplifier |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | AD8040 |
| Pin Count | 14 |
| Qualification Status | Not Qualified |
| Output Type | Rail-to-Rail |
| Number of Elements | 4 |
| Power Supplies | +-1.35/+-6/2.7/12V |
| Operating Supply Current | 6mA |
| Nominal Supply Current | 6mA |
| Quiescent Current | 1.5mA |
| Slew Rate | 63V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 90 dB |
| Current - Input Bias | 1.7μA |
| Voltage - Supply, Single/Dual (±) | 2.7V~12V ±1.35V~6V |
| Input Offset Voltage (Vos) | 5mV |
| Gain Bandwidth Product | 40MHz |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Voltage Gain | 74dB |
| Power Supply Rejection Ratio (PSRR) | 80dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 6.3V |
| Voltage - Input Offset | 2mV |
| Settling Time | 80 ns |
| Current - Output / Channel | 170mA |
| Low-Bias | NO |
| Micropower | NO |
| -3db Bandwidth | 125MHz |
| Bias Current-Max (IIB) @25C | 2.8μA |
| Programmable Power | NO |
| Input Capacitance | 2pF |
| Neg Supply Voltage-Max (Vsup) | -6.3V |
| Wideband | YES |
| Height Seated (Max) | 1.2mm |
| Length | 5mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 4 weeks ago) |
| Mounting Type | Surface Mount |
| Package / Case | 14-TSSOP (0.173, 4.40mm Width) |
| Surface Mount | YES |
| Number of Pins | 14 |
AD8040ARUZ Overview
There is a 14-TSSOP (0.173, 4.40mm Width) case package that contains the instrumentation amplifiers. A General Purpose-type buffer amplifier is shown here. Linear amplifier is delivered in a Tube case. It is estimated that there will be at least 14 terminations this year. It consists of a total of 14 pins in total. Please take in mind that this instrumentation amplifier should be run at 5V. It should be noted that this op amp is a type of Operational Amplifier device. Linear amplifier includes 14 pins. With regards to the offset voltage of the input, buffer amplifier is rated at 5mV. This electronic component is recommended to be mounted using the mounting type Surface Mount. It is important to note that this linear amplifier works well at a temperature of -40°C~125°C when it comes to operating temperatureYou can run this op amp ic on 6mA . Keeping the voltage gain at 74dB is the best course of action. One of its many advantages is that buffer op amp outputs Rail-to-Rail signals. Op amp has total of 4 elements. As a result, linear amplifier's quiescent current is 1.5mA.
AD8040ARUZ Features
14 Pins
supply voltage of 5V
74dB voltage gain
Output Type: Rail-to-Rail
AD8040ARUZ Applications
There are a lot of Analog Devices Inc. AD8040ARUZ Instrumentational OP Amps applications.
- Signal amplification
- Measurements of Wheatstone bridge
- Hand-held batteries
- E-book readers
- Oscilloscopes
- Industrial control system
- Signal filtering
- Proportional counter tubes
- Communication
- Inverse/same-phase proportional circuit
