AD8065ART-R2
| Parameters | |
|---|---|
| Packaging | Tape & Reel (TR) |
| Series | FastFET™ |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Discontinued |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 5 |
| ECCN Code | EAR99 |
| Subcategory | Operational Amplifier |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Reach Compliance Code | not_compliant |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | AD8065 |
| Pin Count | 5 |
| Qualification Status | Not Qualified |
| Output Type | Rail-to-Rail |
| Number of Channels | 1 |
| Operating Supply Current | 6.6mA |
| Nominal Supply Current | 7.4mA |
| Quiescent Current | 7.4mA |
| Slew Rate | 180V/μs |
| Amplifier Type | Voltage Feedback |
| Common Mode Rejection Ratio | 100 dB |
| Current - Input Bias | 3pA |
| Voltage - Supply, Single/Dual (±) | 5V~24V ±2.5V~12V |
| Output Current per Channel | 30mA |
| Input Offset Voltage (Vos) | 400μV |
| Gain Bandwidth Product | 60MHz |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Voltage Gain | 113dB |
| Power Supply Rejection Ratio (PSRR) | 78dB |
| Frequency Compensation | NO |
| -3db Bandwidth | 145MHz |
| Input Capacitance | 2.1pF |
| Length | 2.9mm |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
| Contact Plating | Lead, Tin |
| Mounting Type | Surface Mount |
| Package / Case | SC-74A, SOT-753 |
| Surface Mount | YES |
| Number of Pins | 5 |
| Operating Temperature | -40°C~85°C |
AD8065ART-R2 Overview
In order to protect the op amps, a SC-74A, SOT-753 case is used. A Voltage Feedback-type buffer amplifier is shown here. As far as the packaging is concerned, buffer op amp is delivered in a Tape & Reel (TR) case. The number of terminations is approaching the 5 mark. Buffer amplifier has a total of 5 pins. I would like you to keep in mind that this buffer amplifier needs to be run at a voltage of 5V. It should be noted that this op amp is a type of Operational Amplifier device. The op amp ic has an array of 5 pins on it. Op amp ic rates 400μV for input offset voltage. For this electronic part, it is recommended that you mount it with type Surface Mount. Regarding the operating temperature of this device, instrumentation amplifier performs well at a temperature of -40°C~85°C . This op amp can operate from a supply current at 6.6mA. It is recommended to keep the voltage gain at 113dB at all times. Op amp ic has 1 channels. A benefit of this op amp ic is that it outputs Rail-to-Rail signals, which is one of the many advantages it has to offer. In this case, FastFET? represents the instrumentation amplifiers' series number. The quiescent current is 7.4mA.
AD8065ART-R2 Features
5 Pins
supply voltage of 5V
113dB voltage gain
Output Type: Rail-to-Rail
AD8065ART-R2 Applications
There are a lot of Analog Devices Inc. AD8065ART-R2 Instrumentational OP Amps applications.
- Integrator circuits
- Division circuits
- High/low-pass filter circuit
- Signal transformation
- Strain gauges
- Television
- Portable electronic products powered by batteries
- Home audio systems
- Logarithmic operation circuits
- Navigation
