Parameters |
Contact Plating |
Lead, Tin |
Mounting Type |
Surface Mount |
Package / Case |
8-SOIC (0.154, 3.90mm Width) |
Surface Mount |
YES |
Number of Pins |
8 |
Operating Temperature |
-40°C~85°C |
Packaging |
Tape & Reel (TR) |
JESD-609 Code |
e0 |
Pbfree Code |
no |
Part Status |
Obsolete |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
8 |
ECCN Code |
EAR99 |
Subcategory |
Operational Amplifier |
Packing Method |
TAPE AND REEL |
Technology |
BIPOLAR |
Terminal Position |
DUAL |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
235 |
Number of Functions |
2 |
Supply Voltage |
15V |
Reach Compliance Code |
not_compliant |
Time@Peak Reflow Temperature-Max (s) |
20 |
Base Part Number |
AD822 |
Pin Count |
8 |
Qualification Status |
Not Qualified |
Output Type |
Rail-to-Rail |
Number of Channels |
2 |
Operating Supply Current |
1.8mA |
Quiescent Current |
900μA |
Slew Rate |
3V/μs |
Architecture |
VOLTAGE-FEEDBACK |
Amplifier Type |
General Purpose |
Common Mode Rejection Ratio |
80 dB |
Current - Input Bias |
2pA |
Voltage - Supply, Single/Dual (±) |
5V~30V ±2.5V~15V |
Output Current per Channel |
20mA |
Input Offset Voltage (Vos) |
1.5mV |
Gain Bandwidth Product |
1.9MHz |
Neg Supply Voltage-Nom (Vsup) |
-15V |
Unity Gain BW-Nom |
1900 kHz |
Voltage Gain |
120dB |
Power Supply Rejection Ratio (PSRR) |
80dB |
Low-Offset |
NO |
Frequency Compensation |
YES |
Voltage - Input Offset |
400μV |
Settling Time |
4.5 μs |
Low-Bias |
YES |
Micropower |
YES |
Dual Supply Voltage |
3V |
Input Capacitance |
2.8pF |
Input Voltage Noise Density |
25nV/sqrt Hz |
Height |
1.5mm |
Length |
5mm |
Width |
4mm |
RoHS Status |
Non-RoHS Compliant |
Lead Free |
Contains Lead |
AD822AR-REEL Overview
Op amp is packaged in 8-SOIC (0.154, 3.90mm Width) case. An op amp of this type is a General Purpose-type. As far as the packaging is concerned, buffer op amp is delivered in a Tape & Reel (TR) case. It is estimated that there will be 8 terminations in the next few months. There are a total of 8 pins on this op amp. It would be helpful if you could remember that this op amp ic should be powered by an 15V battery. It should be noted that this type of buffer amplifier is exactly what is known as a Operational Amplifier device. 8 pins are included on the operational amplifiers. Op amp ic rates 1.5mV for input offset voltage. This electrical part should be mounted using type Surface Mount. In terms of operating temperature, this instrumentation amplifier performs well at a temperature of about -40°C~85°C . Using an 1.8mA supply current, this operational amplifier ics can be operated. There should be no change in the voltage gain at 120dB. Buffer op amp is equipped with 2 channels on the device. There are more than a few advantages to using this instrumentation amplifier, one of which is that it outputs Rail-to-Rail signals. For the packing of the instrumentation amplifier, TAPE AND REEL is adopted. Buffer amplifier has a quiescent current of 900μA.
AD822AR-REEL Features
8 Pins
supply voltage of 15V
120dB voltage gain
Output Type: Rail-to-Rail
AD822AR-REEL Applications
There are a lot of Analog Devices Inc. AD822AR-REEL Instrumentational OP Amps applications.
- High input resistance broadband
- Professional videography
- Active probe
- Weak signal detection
- Test equipment
- Switching amplifier
- Displayers for aircraft and air transportation control systems
- Laptop
- Fission chambers
- Measurements of Wheatstone bridge