banner_page

AD822BR

2 Channels 20mA per Channel 2pA 80 dB Instrumentational OP Amps 5V~30V ±2.5V~15V AD822 8 Pins 8-SOIC (0.154, 3.90mm Width)


  • Manufacturer: Analog Devices Inc.
  • Nocochips NO: 84-AD822BR
  • Package: 8-SOIC (0.154, 3.90mm Width)
  • Datasheet: PDF
  • Stock: 294
  • Description: 2 Channels 20mA per Channel 2pA 80 dB Instrumentational OP Amps 5V~30V ±2.5V~15V AD822 8 Pins 8-SOIC (0.154, 3.90mm Width)(Kg)

Details

Tags

Parameters
Contact Plating Lead, Tin
Mount Surface Mount
Mounting Type Surface Mount
Package / Case 8-SOIC (0.154, 3.90mm Width)
Number of Pins 8
Operating Temperature -40°C~85°C
Packaging Tube
JESD-609 Code e0
Pbfree Code no
Part Status Obsolete
Moisture Sensitivity Level (MSL) 1 (Unlimited)
Number of Terminations 8
ECCN Code EAR99
Subcategory Operational Amplifier
Technology BIPOLAR
Terminal Position DUAL
Terminal Form GULL WING
Peak Reflow Temperature (Cel) 235
Number of Functions 2
Supply Voltage 15V
Time@Peak Reflow Temperature-Max (s) 20
Base Part Number AD822
Pin Count 8
Output Type Rail-to-Rail
Number of Channels 2
Operating Supply Current 1.8mA
Nominal Supply Current 1.8mA
Quiescent Current 900μA
Slew Rate 3V/μs
Architecture VOLTAGE-FEEDBACK
Amplifier Type General Purpose
Common Mode Rejection Ratio 80 dB
Current - Input Bias 2pA
Voltage - Supply, Single/Dual (±) 5V~30V ±2.5V~15V
Output Current per Channel 20mA
Input Offset Voltage (Vos) 1.5mV
Bandwidth 1.9MHz
Neg Supply Voltage-Nom (Vsup) -15V
Unity Gain BW-Nom 1900 kHz
Voltage Gain 120dB
Power Supply Rejection Ratio (PSRR) 80dB
Low-Offset NO
Frequency Compensation YES
Voltage - Input Offset 300μV
Settling Time 4.5 μs
Low-Bias YES
Micropower YES
Input Capacitance 2.8pF
Input Voltage Noise Density 25nV/sqrt Hz
Height Seated (Max) 1.75mm
Length 4.9mm
Radiation Hardening No
REACH SVHC No SVHC
RoHS Status Non-RoHS Compliant
Lead Free Contains Lead

AD822BR Overview


Packaging for the buffer amplifier is in the form of a 8-SOIC (0.154, 3.90mm Width) case. A General Purpose-type buffer amplifier is shown here. The case in which buffer amplifier is delivered is called a Tube case. During the past two weeks, there have been close to 8 terminations. It consists of a total of 8 pins in total. Please take in mind that op amp should be run at 15V. A type of Operational Amplifier op amp ic can be identified by the fact that this is a type of Operational Amplifier device. 8 pins are located on the operational amplifiers. Op amp ic rates 1.5mV for input offset voltage. This electrical part should be mounted using type Surface Mount. With regard to operating temperature, this op amp functions well at -40°C~85°C. It is possible to operate this buffer amplifier from a supply current of 1.8mA . It is recommended to keep the voltage gain at 120dB at all times. There are 2 channels on the operational amplifiers. A benefit of this op amp ic is that it outputs Rail-to-Rail signals, which is one of the many advantages it has to offer. The current is quiescent at 900μA.

AD822BR Features


8 Pins
supply voltage of 15V
120dB voltage gain
Output Type: Rail-to-Rail

AD822BR Applications


There are a lot of Analog Devices Inc. AD822BR Instrumentational OP Amps applications.

  • Signal operation
  • RF cable systems
  • Precision measurement
  • Weak signal detection
  • Multiplication circuits
  • Medical instruments
  • single/dual op amp sum and difference circuits
  • Switching amplifier
  • High-frequency data acquisition systems
  • Band-stop filter

Write a review

Note: HTML is not translated!
    Bad           Good