AD822TRZ-EP
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 3 weeks ago) |
| Contact Plating | Tin |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C |
| Packaging | Tube |
| JESD-609 Code | e4 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | AD822 |
| Pin Count | 8 |
| Qualification Status | Not Qualified |
| Output Type | Rail-to-Rail |
| Number of Channels | 2 |
| Operating Supply Current | 1.8mA |
| Quiescent Current | 900μA |
| Slew Rate | 3V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 80 dB |
| Current - Input Bias | 2pA |
| Voltage - Supply, Single/Dual (±) | 5V~30V ±2.5V~15V |
| Output Current per Channel | 20mA |
| Input Offset Voltage (Vos) | 1.5mV |
| Bandwidth | 1.9MHz |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Unity Gain BW-Nom | 1900 kHz |
| Voltage Gain | 120dB |
| Average Bias Current-Max (IIB) | 0.006μA |
| Power Supply Rejection Ratio (PSRR) | 80dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Voltage - Input Offset | 800μV |
| Settling Time | 4.5 μs |
| Low-Bias | YES |
| Micropower | YES |
| Input Capacitance | 2.8pF |
| Input Voltage Noise Density | 25nV/sqrt Hz |
| Height | 1.5mm |
| Length | 5mm |
| Width | 4mm |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
AD822TRZ-EP Overview
In the package, you will find a 8-SOIC (0.154, 3.90mm Width)-case to contain the op amp ic. Buffer amps of this type are called General Purpose-types. It comes in a Tube case, which protects instrumentation amplifier from damage during delivery. During the past two weeks, there have been close to 8 terminations. The pins on this board total to 8 in total. The linear amplifier should be run at 5V at all times, so please keep that in mind when using it. This particular linear amplifier is a type of Operational Amplifier device, to be precise. The buffer op amp includes 8 pins. In terms of the input offset voltage, instrumentation amplifier rates at 1.5mV. The mounting type that is recommended for this electrical part is Surface Mount. With regard to operating temperature, this op amp functions well at -40°C~85°C. Using an 1.8mA supply current, this operational amplifier ics can be operated. 120dB should remain the voltage gain. There are a total of 2 channels available on the op amps. As one of the many benefits of this buffer amplifier, it puts out Rail-to-Rail signals, which is one of the many benefits it offers. There is an 900μA quiescent current in linear amplifier.
AD822TRZ-EP Features
8 Pins
supply voltage of 5V
120dB voltage gain
Output Type: Rail-to-Rail
AD822TRZ-EP Applications
There are a lot of Analog Devices Inc. AD822TRZ-EP Instrumentational OP Amps applications.
- Voltage regulation circuit
- Measurements of Wheatstone bridge
- High gain DC amplifier
- Radar
- Weak signal detection
- Inverse/same-phase proportional circuit
- Large motor controllers
- Television broadcasting equipment
- Division circuits
- Weighing systems
