AD822TRZ-EP-R7
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 3 weeks ago) |
| Contact Plating | Gold |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C |
| Packaging | Digi-Reel® |
| JESD-609 Code | e4 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | AD822 |
| Pin Count | 8 |
| Qualification Status | Not Qualified |
| Output Type | Rail-to-Rail |
| Number of Elements | 2 |
| Operating Supply Current | 1.8mA |
| Quiescent Current | 900μA |
| Slew Rate | 3V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 80 dB |
| Current - Input Bias | 2pA |
| Voltage - Supply, Single/Dual (±) | 5V~30V ±2.5V~15V |
| Output Current per Channel | 20mA |
| Input Offset Voltage (Vos) | 1.5mV |
| Gain Bandwidth Product | 1.9MHz |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Unity Gain BW-Nom | 1900 kHz |
| Voltage Gain | 120dB |
| Average Bias Current-Max (IIB) | 0.006μA |
| Power Supply Rejection Ratio (PSRR) | 80dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Voltage - Input Offset | 800μV |
| Settling Time | 4.5 μs |
| Low-Bias | YES |
| Micropower | YES |
| Input Capacitance | 2.8pF |
| Input Voltage Noise Density | 25nV/sqrt Hz |
| Height Seated (Max) | 1.75mm |
| Length | 4.9mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
AD822TRZ-EP-R7 Overview
There is a 8-SOIC (0.154, 3.90mm Width) case package that contains the instrumentation amplifiers. There are two types of operational amplifiers in this circuit. The op amp is delivered to you in a Digi-Reel? case. The number of terminations approaches 8. A total of 8 pins are attached to buffer op amp. It would be helpful if you could remember that this op amp ic should be powered by an 5V battery. There are two types of Operational Amplifier op amps in this case, and this device falls into one of them. It has 8 pins that make up the linear amplifier. Regarding input offset voltage, buffer amplifier rates 1.5mV voltage. Surface Mount is the recommended mounting type for this linear amplifier. It is recommended that this op amp ic be operated at a temperature no higher than -40°C~85°C for optimal performance. As long as the supply current of the chip does not exceed 1.8mA, this op amp ic can operate. It is a member of the 120dB's 120dB family. In addition to outputting Rail-to-Rail signals, this op amp ic offers a number of other advantages. Depending on the chip's operating supply voltage, op amp ic has a rated voltage of 2. A TAPE AND REEL-shaped amplifier is used to pack the buffer amps. There is an 900μA quiescent current running through op amp ic.
AD822TRZ-EP-R7 Features
8 Pins
supply voltage of 5V
120dB voltage gain
Output Type: Rail-to-Rail
AD822TRZ-EP-R7 Applications
There are a lot of Analog Devices Inc. AD822TRZ-EP-R7 Instrumentational OP Amps applications.
- Semiconductor detectors
- Logarithmic operation circuits
- Scintillation detectors
- Navigation
- Medical imaging
- Video data acquisition
- Band-stop filter
- Medical instruments
- Switching amplifier
- E-book readers
