AD827JR-16
| Parameters | |
|---|---|
| Input Offset Voltage (Vos) | 500μV |
| Bandwidth | 50MHz |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Unity Gain BW-Nom | 35000 kHz |
| Voltage Gain | 70.88dB |
| Power Supply Rejection Ratio (PSRR) | 75dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 18V |
| Bias Current-Max (IIB) @25C | 7μA |
| Input Capacitance | 1.5pF |
| Neg Supply Voltage-Max (Vsup) | -18V |
| Input Voltage Noise Density | 15nV/sqrt Hz |
| Length | 10.3mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
| Contact Plating | Lead, Tin |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.295, 7.50mm Width) |
| Surface Mount | YES |
| Number of Pins | 16 |
| Operating Temperature | 0°C~70°C |
| Packaging | Tube |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Terminal Finish | Tin/Lead (Sn85Pb15) |
| Subcategory | Operational Amplifier |
| Max Power Dissipation | 1.5W |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 2 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | AD827 |
| Pin Count | 16 |
| Power Supplies | +-5/+-15V |
| Number of Channels | 2 |
| Operating Supply Current | 10.5mA |
| Power Dissipation | 1.5W |
| Quiescent Current | 6.75mA |
| Slew Rate | 300V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 95 dB |
| Current - Input Bias | 3.3μA |
| Voltage - Supply, Single/Dual (±) | ±4.5V~18V |
| Output Current per Channel | 32mA |
AD827JR-16 Overview
In the package, you will find a 16-SOIC (0.295, 7.50mm Width)-case to contain the op amp ic. There are two types of operational amplifiers in this circuit. A Tube case is used to deliver the buffer op amp. It is estimated that there will be 16 terminations in the next few months. A total of 16 pins are located on this board. It would be helpful if you could remember that this op amp ic should be powered by an 5V battery. To be specific, this instrumentation amplifier is a type of Operational Amplifier. The op amp ic has an array of 16 pins on it. Regarding input offset voltage, buffer amplifier rates 500μV voltage. For this electronic part, it is recommended that you mount it with type Surface Mount. With regard to operating temperature, op amp ranges 0°C~70°C. You can run this op amp ic on 10.5mA . Op amp is a member of the 70.88dB's 70.88dB family. As far as the device is concerned, buffer amplifier has 2 channels. The current is quiescent at 6.75mA.
AD827JR-16 Features
16 Pins
supply voltage of 5V
70.88dB voltage gain
AD827JR-16 Applications
There are a lot of Analog Devices Inc. AD827JR-16 Instrumentational OP Amps applications.
- High gain DC amplifier
- High speed sample
- PDA
- Switching amplifier
- Proportional counter tubes
- Oscilloscopes
- Proportional operation circuits
- Television
- Weighing systems
- Automation control systems
