AD8295BCPZ-R7
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 4 months ago) |
| Contact Plating | Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-VQFN, CSP |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e3 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 3 (168 Hours) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 100GOhm |
| Terminal Position | QUAD |
| Terminal Form | NO LEAD |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | AD8295 |
| Pin Count | 16 |
| Qualification Status | Not Qualified |
| Operating Supply Voltage | 36V |
| Number of Channels | 1 |
| Number of Circuits | 3 |
| Operating Supply Current | 2.3mA |
| Nominal Supply Current | 2.3mA |
| Slew Rate | 2V/μs |
| Amplifier Type | Instrumentation |
| Common Mode Rejection Ratio | 140 dB |
| Current - Input Bias | 200pA |
| Voltage - Supply, Single/Dual (±) | 4.6V~36V ±2.3V~18V |
| Output Current per Channel | 18mA |
| Input Offset Voltage (Vos) | 120μV |
| Bandwidth | 750 kHz |
| Gain Bandwidth Product | 1MHz |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Voltage Gain | 60dB |
| Voltage - Input Offset | 60μV |
| -3db Bandwidth | 1.2MHz |
| Input Offset Current-Max (IIO) | 0.0006μA |
| Voltage Gain-Nom | 10 |
| Non-linearity-Max | 0.002% |
| Length | 4mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
AD8295BCPZ-R7 Overview
Packaging for the buffer amplifier is in the form of a 16-VQFN, CSP case. An op amp of this type is a Instrumentation-type. A Tape & Reel (TR) case is used to deliver the buffer op amp. It is estimated that there will be 16 terminations in the next few months. Buffer amplifier has a total of 16 pins on it. I would like you to keep in mind that this buffer amplifier needs to be run at a voltage of 15V. The buffer op amp includes 16 pins. In terms of the input offset voltage, instrumentation amplifier rates at 120μV. This electronic component is recommended to be mounted using the mounting type Surface Mount. It is recommended that this op amp ic be operated at a temperature no higher than -40°C~85°C for optimal performance. An 2.3mA volt supply current is needed for this linear amplifier to operate. You should keep the voltage gain at 60dB for the time being. On this instrumentation amplifier, there are 3 circuits that are connected together. 1 channels are available on the instrumentation amplifier. The operating supply voltage of the buffer op amp is rated at 36V. In order for the buffer amplifier resistance to remain within the 100GOhm range, the device should be tested.
AD8295BCPZ-R7 Features
16 Pins
supply voltage of 15V
60dB voltage gain
Resistance of 100GOhm
AD8295BCPZ-R7 Applications
There are a lot of Analog Devices Inc. AD8295BCPZ-R7 Instrumentational OP Amps applications.
- Automation control systems
- Addition operation circuits
- Portable electronic products powered by batteries
- Navigation
- Industrial control system
- Biopotential
- Instrumentation
- Television broadcasting equipment
- ECG equipment
- Power control
