AD8426BCPZ-R7
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 4 weeks ago) |
| Contact Plating | Tin |
| Mounting Type | Surface Mount |
| Package / Case | 16-VQFN, CSP |
| Surface Mount | YES |
| Number of Pins | 16 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e3 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 3 (168 Hours) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 800MOhm |
| Technology | BIPOLAR |
| Terminal Position | QUAD |
| Terminal Form | NO LEAD |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | AD8426 |
| Pin Count | 16 |
| Qualification Status | Not Qualified |
| Output Type | Rail-to-Rail |
| Number of Channels | 2 |
| Operating Supply Current | 350μA |
| Nominal Supply Current | 350μA |
| Slew Rate | 0.6V/μs |
| Amplifier Type | Instrumentation |
| Common Mode Rejection Ratio | 110 dB |
| Current - Input Bias | 20nA |
| Voltage - Supply, Single/Dual (±) | 2.2V~36V ±1.35V~18V |
| Output Current per Channel | 13mA |
| Input Offset Voltage (Vos) | 5μV |
| Bandwidth | 160 kHz |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Voltage Gain | 60dB |
| Supply Voltage Limit-Max | 18V |
| Voltage - Input Offset | 100μV |
| -3db Bandwidth | 1MHz |
| Neg Supply Voltage-Max (Vsup) | -18V |
| Input Offset Current-Max (IIO) | 0.0005μA |
| Voltage Gain-Nom | 10 |
| Non-linearity-Max | 0.075% |
| Height Seated (Max) | 1mm |
| Length | 4mm |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
AD8426BCPZ-R7 Overview
Op amp is packaged in 16-VQFN, CSP case. There are two types of operational amplifiers in this circuit. Linear amplifier is delivered in a Tape & Reel (TR) case. It is estimated that there will be 16 terminations in the next few months. The pins on this board total to 16 in total. I would like to remind you that this buffer op amp should be powered by an 15V battery. A total of 16 pins are present on the instrumentation amplifier. Regarding input offset voltage, buffer amplifier rates 5μV voltage. For this electronic part, it is recommended that you mount it with type Surface Mount. According to the manufacturer, this buffer op amp works well at -40°C~125°C , which is a good operating temperature. In order for this instrumentation amplifier to operate, the supply current needs to be between 350μA and 10 . It is recommended to keep the voltage gain at 60dB at all times. The op amp ic has 2 channels on it. There are more than a few advantages to using this instrumentation amplifier, one of which is that it outputs Rail-to-Rail signals. Instrumentation amplifier resistance should remain within the range of 800MOhm.
AD8426BCPZ-R7 Features
16 Pins
supply voltage of 15V
60dB voltage gain
Output Type: Rail-to-Rail
Resistance of 800MOhm
AD8426BCPZ-R7 Applications
There are a lot of Analog Devices Inc. AD8426BCPZ-R7 Instrumentational OP Amps applications.
- PDA
- Signal amplification
- Radar
- High input resistance broadband
- Multiplication circuits
- High/low-pass filter circuit
- earphone
- Inverse/same-phase proportional circuit
- Communication
- Communication device
