AD845JNZ
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 3 months ago) |
| Contact Plating | Tin |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 8-DIP (0.300, 7.62mm) |
| Number of Pins | 8 |
| Operating Temperature | 0°C~70°C |
| Packaging | Tube |
| JESD-609 Code | e3 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Subcategory | Operational Amplifier |
| Max Power Dissipation | 1.6W |
| Technology | BIPOLAR |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Terminal Pitch | 2.54mm |
| Base Part Number | AD845 |
| Pin Count | 8 |
| Number of Channels | 1 |
| Operating Supply Current | 10mA |
| Nominal Supply Current | 10mA |
| Power Dissipation | 1.6W |
| Output Current | 50mA |
| Quiescent Current | 10mA |
| Slew Rate | 100V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | J-FET |
| Common Mode Rejection Ratio | 110 dB |
| Current - Input Bias | 750pA |
| Max Input Voltage | 18V |
| Voltage - Supply, Single/Dual (±) | ±4.75V~18V |
| Output Current per Channel | 50mA |
| Supply Type | Dual |
| Input Offset Voltage (Vos) | 250μV |
| Bandwidth | 16MHz |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Unity Gain BW-Nom | 16000 kHz |
| Voltage Gain | 113.98dB |
| Average Bias Current-Max (IIB) | 0.045μA |
| Power Supply Rejection Ratio (PSRR) | 110dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Voltage - Input Offset | 700μV |
| Bias Current-Max (IIB) @25C | 0.002μA |
| Dual Supply Voltage | 15V |
| Input Capacitance | 4pF |
| Height | 3.43mm |
| Length | 9.27mm |
| Width | 7.24mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
AD845JNZ Overview
There is a 8-DIP (0.300, 7.62mm) case in which the instrumentation amplifier is packaged. J-FET-type instrumentation amplifiers are used in this application. A Tube case is used to deliver the buffer op amp. During the past two weeks, there have been close to 8 terminations. Linear amplifier has a total of 8 pins. Please take in mind that this instrumentation amplifier should be run at 15V. In more specific terms, this linear amplifier can be categoriOperational Amplifiered as a Operational Amplifier-type device. In total, the buffer amplifier consists of 8 pins. Op amp ic rates 250μV for input offset voltage. This electronic part is recommended for mounting type Through Hole. In terms of operating temperature, this instrumentation amplifier is well suited to a temperature range of 0°C~70°C. You can run this op amp ic on 10mA . Keeping the voltage gain at 113.98dB is the best course of action. The op amp ic has 1 channels on it. Buffer amplifier has a quiescent current of 10mA.
AD845JNZ Features
8 Pins
supply voltage of 15V
113.98dB voltage gain
AD845JNZ Applications
There are a lot of Analog Devices Inc. AD845JNZ Instrumentational OP Amps applications.
- Scintillation detectors
- Power generator
- Communication
- Measurements of Wheatstone bridge
- Addition operation circuits
- Non-polarized electrodes
- Integrator circuits
- High gain DC amplifier
- Large motor controllers
- Instrumentation
