AD847JR-REEL7
| Parameters | |
|---|---|
| Contact Plating | Lead, Tin |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | 0°C~70°C |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL |
| Max Power Dissipation | 800mW |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Reach Compliance Code | not_compliant |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | AD847 |
| Pin Count | 8 |
| Qualification Status | Not Qualified |
| Number of Channels | 1 |
| Operating Supply Current | 5.3mA |
| Power Dissipation | 800mW |
| Quiescent Current | 4.8mA |
| Supply Current-Max | 7.6mA |
| Slew Rate | 300V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 95 dB |
| Current - Input Bias | 3.3μA |
| Voltage - Supply, Single/Dual (±) | ±4.5V~18V |
| Output Current per Channel | 32mA |
| Input Offset Voltage (Vos) | 1mV |
| Gain Bandwidth Product | 50MHz |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Unity Gain BW-Nom | 35000 kHz |
| Voltage Gain | 70.88dB |
| Average Bias Current-Max (IIB) | 7.2μA |
| Power Supply Rejection Ratio (PSRR) | 86dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Voltage - Input Offset | 500μV |
| Settling Time | 120 ns |
| Bias Current-Max (IIB) @25C | 6.6μA |
| Input Capacitance | 1.5pF |
| Input Voltage Noise Density | 15nV/sqrt Hz |
| Height Seated (Max) | 2.59mm |
| Length | 4.9mm |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
AD847JR-REEL7 Overview
A 8-SOIC (0.154, 3.90mm Width) case is used to package the op amp. Op amps are General Purpose types of amplifier on the chip. It comes in a Tape & Reel (TR) case, which protects instrumentation amplifier from damage during delivery. We are approaching the 8h termination of the year. In this case, there are 8 pins on the board. It would be helpful if you could remember that this op amp ic should be powered by an 5V battery. A type of Operational Amplifier buffer op amp is what this device is specifically, to be more precise. There are 8 pins on this chip. As far as the input offset voltage is concerned, linear amplifier rates at 1mV. Surface Mount is the recommended mounting type for this linear amplifier. According to the manufacturer, this buffer op amp works well at 0°C~70°C , which is a good operating temperature. An 5.3mA volt supply current is needed for this linear amplifier to operate. There should be no change in the voltage gain at 70.88dB. There are 1 channels on the operational amplifiers. To pack the operational amplifier ics, TAPE AND REEL is adopted as the packing method. As a result, linear amplifier's quiescent current is 4.8mA.
AD847JR-REEL7 Features
8 Pins
supply voltage of 5V
70.88dB voltage gain
AD847JR-REEL7 Applications
There are a lot of Analog Devices Inc. AD847JR-REEL7 Instrumentational OP Amps applications.
- Commercial audio systems
- Blood pressure sensors
- Active probe
- Proportional counter tubes
- Signal transformation
- Cinema or auditorium audio system
- Integrator circuits
- Communication device
- Portable docking station
- Portable media players
