AD8510AR
| Parameters | |
|---|---|
| Contact Plating | Lead, Tin |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tube |
| JESD-609 Code | e0 |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Subcategory | Operational Amplifier |
| Technology | JFET |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Reach Compliance Code | not_compliant |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | AD8510 |
| Pin Count | 8 |
| Qualification Status | Not Qualified |
| Number of Channels | 1 |
| Operating Supply Current | 2.2mA |
| Quiescent Current | 2.5mA |
| Supply Current-Max | 2.6mA |
| Slew Rate | 20V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | J-FET |
| Common Mode Rejection Ratio | 86 dB |
| Current - Input Bias | 25pA |
| Voltage - Supply, Single/Dual (±) | ±4.5V~18V |
| Output Current per Channel | 70mA |
| Input Offset Voltage (Vos) | 80μV |
| Gain Bandwidth Product | 8MHz |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Unity Gain BW-Nom | 8000 kHz |
| Voltage Gain | 100.59dB |
| Power Supply Rejection Ratio (PSRR) | 86dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Voltage - Input Offset | 100μV |
| Low-Bias | YES |
| Micropower | NO |
| Programmable Power | NO |
| Wideband | NO |
| Length | 4.9mm |
| RoHS Status | Non-RoHS Compliant |
AD8510AR Overview
In the package, you will find a 8-SOIC (0.154, 3.90mm Width)-case to contain the op amp ic. Buffer amps of this type are called J-FET-types. Instrumentation amplifier is delivered in a Tube case. A total of 8 terminations have been reported in the past few weeks. Buffer amplifier has a total of 8 pins on it. Please take in mind that this instrumentation amplifier should be run at 5V. Instrumentation amplifier is a part of Operational Amplifier. A total of 8 pins are present on the instrumentation amplifier. Regarding input offset voltage, op amp rates 80μV. For this electronic part, it is recommended that you mount it with type Surface Mount. According to the manufacturer, this buffer op amp works well at -40°C~125°C , which is a good operating temperature. As long as the supply current of the chip does not exceed 2.2mA, this op amp ic can operate. It is a member of the 100.59dB's 100.59dB family. Buffer op amp is equipped with 1 channels on the device. 2.5mA quiescent currents are flowing through buffer op amp.
AD8510AR Features
8 Pins
supply voltage of 5V
100.59dB voltage gain
AD8510AR Applications
There are a lot of Analog Devices Inc. AD8510AR Instrumentational OP Amps applications.
- High/low-pass filter circuit
- High input resistance broadband
- Biopotential
- pH (acidity)
- Fission chambers
- Band-pass filter
- RF cable systems
- Integrator circuits
- Laptop
- Division circuits
