AD8513ARZ-REEL7
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 1 week ago) |
| Contact Plating | Tin |
| Mounting Type | Surface Mount |
| Package / Case | 14-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 14 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e3 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL |
| Technology | JFET |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 5V |
| Terminal Pitch | 1.27mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | AD8513 |
| Pin Count | 14 |
| Qualification Status | Not Qualified |
| Power Supplies | +-5/+-15V |
| Number of Channels | 4 |
| Operating Supply Current | 10mA |
| Quiescent Current | 2.5mA |
| Supply Current-Max | 18mA |
| Slew Rate | 20V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | J-FET |
| Common Mode Rejection Ratio | 100 dB |
| Current - Input Bias | 25pA |
| Voltage - Supply, Single/Dual (±) | ±4.5V~18V |
| Output Current per Channel | 70mA |
| Input Offset Voltage (Vos) | 1mV |
| Gain Bandwidth Product | 8MHz |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Unity Gain BW-Nom | 8000 kHz |
| Voltage Gain | 100.59dB |
| Average Bias Current-Max (IIB) | 0.0075μA |
| Power Supply Rejection Ratio (PSRR) | 130dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 18V |
| Voltage - Input Offset | 100μV |
| Settling Time | 900 ns |
| Low-Bias | YES |
| Micropower | NO |
| Bias Current-Max (IIB) @25C | 0.00003μA |
| Programmable Power | NO |
| Neg Supply Voltage-Max (Vsup) | -18V |
| Wideband | NO |
| Input Voltage Noise Density | 34nV/sqrt Hz |
| Height | 1.5mm |
| Length | 8.75mm |
| Width | 4mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
AD8513ARZ-REEL7 Overview
Op amp is packaged in 14-SOIC (0.154, 3.90mm Width) case. This is a J-FET type op amp. Upon delivery, op amp ic is packaged in a Tape & Reel (TR) case. A total of 14 terminations have been reported in the past few weeks. In this case, there are 14 pins on the board. I would like you to keep in mind that this buffer amplifier needs to be run at a voltage of 5V. I would like to specify that this buffer amplifier belongs to the Operational Amplifier-type of devices. The op amp ic has an array of 14 pins on it. Op amp ic rates 1mV for input offset voltage. This electronic part is recommended for mounting type Surface Mount. It is recommended that this op amp ic be operated at a temperature no higher than -40°C~125°C for optimal performance. A supply current of 10mA can be used to operate this linear amplifier. You should keep the voltage gain at 100.59dB for the time being. As far as the device is concerned, buffer amplifier has 4 channels. This linear amplifier pack is based on the TAPE AND REEL axis. Currently, linear amplifier is operating with a quiescent current of 2.5mA.
AD8513ARZ-REEL7 Features
14 Pins
supply voltage of 5V
100.59dB voltage gain
AD8513ARZ-REEL7 Applications
There are a lot of Analog Devices Inc. AD8513ARZ-REEL7 Instrumentational OP Amps applications.
- Radar
- Semiconductor detectors
- Communication
- Large motor controllers
- Addition operation circuits
- Comparator
- RF cable systems
- Communication device
- Automotive sensors
- Measurements of Wheatstone bridge
