AD8515ARTZ-REEL7
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 3 weeks ago) |
| Contact Plating | Tin |
| Mounting Type | Surface Mount |
| Package / Case | SC-74A, SOT-753 |
| Surface Mount | YES |
| Number of Pins | 5 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e3 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 5 |
| ECCN Code | EAR99 |
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 3V |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | AD8515 |
| Pin Count | 5 |
| Output Type | Rail-to-Rail |
| Operating Supply Voltage | 3V |
| Number of Channels | 1 |
| Operating Supply Current | 500μA |
| Nominal Supply Current | 410μA |
| Quiescent Current | 500μA |
| Slew Rate | 2.7V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 50 dB |
| Current - Input Bias | 5pA |
| Max Input Voltage | 5V |
| Voltage - Supply, Single/Dual (±) | 1.8V~5V |
| Output Current per Channel | 20mA |
| Supply Type | Single |
| Input Offset Voltage (Vos) | 6mV |
| Bandwidth | 5MHz |
| Unity Gain BW-Nom | 5000 kHz |
| Voltage Gain | 126.02dB |
| Average Bias Current-Max (IIB) | 0.008μA |
| Power Supply Rejection Ratio (PSRR) | 85dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 6V |
| Voltage - Input Offset | 1mV |
| Low-Bias | YES |
| Micropower | YES |
| Bias Current-Max (IIB) @25C | 0.00003μA |
| Programmable Power | NO |
| Length | 2.9mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
AD8515ARTZ-REEL7 Overview
The linear amplifier is packaged in a SC-74A, SOT-753 case which makes it easy for the consumer to handle. An op amp of this type is a General Purpose-type. As far as the packaging is concerned, buffer op amp is delivered in a Tape & Reel (TR) case. The number of terminations is approaching the 5 mark. Buffer amplifier has a total of 5 pins on it. I would like you to keep in mind that this buffer amplifier needs to be run at a voltage of 3V. This particular linear amplifier is a type of Operational Amplifier device, to be precise. An 5-pin op amp ic is included in the package. Regarding input offset voltage, buffer amplifier rates 6mV voltage. This electrical part should be mounted using type Surface Mount. According to the manufacturer, this buffer op amp works well at -40°C~125°C , which is a good operating temperature. As long as the supply current of the chip does not exceed 500μA, this op amp ic can operate. Op amp is a member of the 126.02dB's 126.02dB family. There are a total of 1 channels available on the op amps. One of its many advantages is that buffer op amp outputs Rail-to-Rail signals. The operating supply voltage of instrumentation amplifier is rated 3V voltage. A TAPE AND REEL-shaped amplifier is used to pack the buffer amps. Currently, linear amplifier is operating with a quiescent current of 500μA.
AD8515ARTZ-REEL7 Features
5 Pins
supply voltage of 3V
126.02dB voltage gain
Output Type: Rail-to-Rail
AD8515ARTZ-REEL7 Applications
There are a lot of Analog Devices Inc. AD8515ARTZ-REEL7 Instrumentational OP Amps applications.
- Home audio systems
- Comparator
- Inverse/same-phase proportional circuit
- ECG equipment
- Television
- Power transmission
- Multimedia playback equipment
- Displayers for aircraft and air transportation control systems
- Measurements of Wheatstone bridge
- Strain gauges
