AD8534ARUZ
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 1 week ago) |
| Contact Plating | Tin |
| Mounting Type | Surface Mount |
| Package / Case | 14-TSSOP (0.173, 4.40mm Width) |
| Surface Mount | YES |
| Number of Pins | 14 |
| Operating Temperature | -40°C~85°C |
| Packaging | Tube |
| JESD-609 Code | e3 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Subcategory | Operational Amplifier |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 3V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | AD8534 |
| Pin Count | 14 |
| Output Type | Rail-to-Rail |
| Operating Supply Voltage | 5V |
| Number of Channels | 4 |
| Operating Supply Current | 5mA |
| Quiescent Current | 1.25mA |
| Supply Current-Max | 7mA |
| Slew Rate | 5V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 47 dB |
| Current - Input Bias | 5pA |
| Voltage - Supply, Single/Dual (±) | 2.7V~6V ±1.35V~3V |
| Output Current per Channel | 250mA |
| Input Offset Voltage (Vos) | 25mV |
| Bandwidth | 3MHz |
| Unity Gain BW-Nom | 2200 kHz |
| Voltage Gain | 98.06dB |
| Average Bias Current-Max (IIB) | 0.00006μA |
| Power Supply Rejection Ratio (PSRR) | 55dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 7V |
| Settling Time | 1.4 μs |
| Low-Bias | YES |
| Bias Current-Max (IIB) @25C | 0.00005μA |
| Input Voltage Noise Density | 45nV/sqrt Hz |
| Height | 1mm |
| Length | 5mm |
| Width | 4.4mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
AD8534ARUZ Overview
Packaged in a 14-TSSOP (0.173, 4.40mm Width) case, the buffer op amp is ready to use. An op amp ic of the General Purpose type. Linear amplifier is delivered in a Tube case. During the past two weeks, there have been close to 14 terminations. Buffer amplifier has a total of 14 pins. Please take in mind that this instrumentation amplifier should be run at 3V. There are two types of Operational Amplifier op amps in this case, and this device falls into one of them. There are 14 pins on this chip. Op amp ic rates 25mV for input offset voltage. For this electrical component, the recommended mounting type is Surface Mount, which is the most common. With regard to operating temperature, op amp ranges -40°C~85°C. It is possible to operate this buffer amplifier from a supply current of 5mA . The voltage gain should stay at 98.06dB. Buffer op amp is equipped with 4 channels on the device. This op amp ic outputs Rail-to-Rail signals, which is one of the many benefits it has. The operating supply voltage of instrumentation amplifier is rated 5V voltage. The current is quiescent at 1.25mA.
AD8534ARUZ Features
14 Pins
supply voltage of 3V
98.06dB voltage gain
Output Type: Rail-to-Rail
AD8534ARUZ Applications
There are a lot of Analog Devices Inc. AD8534ARUZ Instrumentational OP Amps applications.
- Television
- Logarithmic operation circuits
- Addition operation circuits
- Large motor controllers
- Fast A/D and D/A converters
- RF cable systems
- Image computer boards
- Proportional counter tubes
- Information processing
- Exponential operation circuits
