AD8541AKSZ-R2
| Parameters | |
|---|---|
| Mounting Type | Surface Mount |
| Package / Case | 5-TSSOP, SC-70-5, SOT-353 |
| Surface Mount | YES |
| Number of Pins | 5 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Pbfree Code | no |
| Part Status | Discontinued |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 5 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 3V |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | AD8541 |
| Pin Count | 5 |
| Output Type | Rail-to-Rail |
| Number of Channels | 1 |
| Operating Supply Current | 45μA |
| Nominal Supply Current | 45μA |
| Output Current | 30mA |
| Quiescent Current | 65μA |
| Slew Rate | 0.92V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 45 dB |
| Current - Input Bias | 4pA |
| Max Input Voltage | 5V |
| Voltage - Supply, Single/Dual (±) | 2.7V~5.5V |
| Output Current per Channel | 30mA |
| Supply Type | Single |
| Input Offset Voltage (Vos) | 1mV |
| Bandwidth | 1MHz |
| Unity Gain BW-Nom | 980 kHz |
| Voltage Gain | 92.04dB |
| Power Supply Rejection Ratio (PSRR) | 65dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 6V |
| Low-Bias | YES |
| Micropower | YES |
| Max Frequency | 10kHz |
| Bias Current-Max (IIB) @25C | 0.00006μA |
| Programmable Power | NO |
| Height | 1mm |
| Length | 2.2mm |
| Width | 1.35mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
AD8541AKSZ-R2 Overview
Packaged in a 5-TSSOP, SC-70-5, SOT-353 case, the buffer op amp is ready to use. An op amp of this type is a General Purpose-type. It comes in a Tape & Reel (TR) case, which protects instrumentation amplifier from damage during delivery. During the past two weeks, there have been close to 5 terminations. Buffer amplifier has a total of 5 pins on it. It is important to remember that this op amp should be operated at a voltage of 3V volts. A type of Operational Amplifier op amp ic can be identified by the fact that this is a type of Operational Amplifier device. 5 pins are available on the instrumentation amplifier. The input offset voltage is 1mV. This electronic component is recommended to be mounted using the mounting type Surface Mount. With regard to operating temperature, op amp ranges -40°C~125°C. An 45μA volt supply current is needed for this linear amplifier to operate. Op amp is a member of the 92.04dB's 92.04dB family. On the buffer amps, there are 1 channels that can be used. As one of the many benefits of this buffer amplifier, it puts out Rail-to-Rail signals, which is one of the many benefits it offers. The instrumentation amplifier is packed in the form of TAPE AND REEL. The quiescent current is 65μA.
AD8541AKSZ-R2 Features
5 Pins
supply voltage of 3V
92.04dB voltage gain
Output Type: Rail-to-Rail
AD8541AKSZ-R2 Applications
There are a lot of Analog Devices Inc. AD8541AKSZ-R2 Instrumentational OP Amps applications.
- Signal amplification
- Navigation
- Comparator
- Scintillation detectors
- PDA
- Video amplifiers
- Power transmission
- Signal filtering
- High-frequency data acquisition systems
- Polarized electrodes
